Module No. 23592359-1
GETTING ACQUAINTED
Congratulations upon your selection of this CASIO watch. To get the most out of your purchase, be sure to carefully read this manual and keep it on hand for later reference when necessary.
"Button operations are indicated using the letters shown in the illustration.
"Each section of this manual provides you with the information you need to perform operations in each mode. Further details and technical information can be
found in the OREFERENCE� section.
Crown
GENERAL GUIDE
"Press C to change from mode to mode.
"In any mode, press L to illuminate the display.
"If the digital display of your watch is continuously changing, see OAuto Display Function� for information on how to stop it.
Timekeeping ModeTelememo ModeWorld Time ModeAlarm ModeStopwatch Mode
Press C.
TIMEKEEPINGDaylight Saving Time (DST)
Daylight Saving Time advances the time setting by one hour from Standard Time.
Use the Timekeeping Mode to set and view the current time and date.Remember that not all countries or even local areas use Daylight Saving Time.
"In the Timekeeping Mode, press D to change the display format as shown below.
To toggle the Timekeeping Mode time between DST and Standard Time
DateDate/TimeAnalog1.In the Timekeeping Mode, hold down A until theGMT differential
second digits start to flash, which indicates the setting
Day of week
YearMonth � Day PM indicatorHour handMinute handscreen.
2.Press C to move the flashing to the DST On/Off
setting.
3.Press D to toggle between Daylight Saving Time and
standard time.
"Note that you cannot switch between standard time
and Daylight Saving Time while is selected as
the city code.
Seconds4.Press A to exit the setting screen.
Hour : MinutesSecond hand"The DST indicator appears on the display to indicate
that daylight saving time is turned on.
Read This Before You Set the Time and Date !
To set the analog time
The digital times displayed in the Timekeeping Mode and World Time Mode are
linked. Because of this, make sure you select a city code for your Home City (the city1.Pull the crown out.
"This causes the second hand to stop.
where you normally use the watch).
2.Set the minute and hour hands by turning the crown.
"This watch features separate digital and analog timekeeping. Note that the digital
time and analog time are independent of each other, and must be set separately.3.Push the crown back in to restart timekeeping.
To set the digital time and date
City code1.In the Timekeeping Mode, hold down A until the
second digits start to flash, which indicates the setting
screen.TELEMEMO
2.Press C to move the flashing in the sequence shownRemaining memoryTelememo lets you store up to 30 records, each
below to select other settings.containing name and telephone number data. Records
Number of records stored
are automatically sorted based on the characters of the
SecondsDSTCity CodeHourname. You can recall records by scrolling through them
on the display.
DayMonthYearMinutes"See OCHARACTER LIST� for details on how the watch
sorts records.
3.When the setting you want to change is flashing, press D to change it as described"The name can show only three characters at a time, so
below.Namelonger text scrolls continuously from right to left.
"All of the operations in this section are performed in the
SettingDo this...Telememo Mode, which you enter by pressing C.
SecondsPress D to reset to 00.
Press D to toggle between Daylight Saving Time and standard
DSTtime. See ODaylight Saving Time (DST)� for details.
City Code, Hour,
Minutes, Year, Press D(+) to change the setting.Telephone number
Month, Day
To create a new Telememo record
"See OCITY CODE TABLE� for a complete list of available codes.Text area1.In the Telememo Mode, press B or D until the new
"Pressing D while the seconds count is in the range of 30 to 59 resets thedata screen appears.
seconds to 00 and adds 1 to the minutes. In the range of 00 to 29, the minutes"The new data screen is the one that is blank (contains
count is unchanged.no name and telephone number).
4.Press A to exit the setting screen."If the message appears on the display, it
means that memory is full. To store another record,
Note
"The day of the week is automatically displayed in accordance with the date (year,you will first have to delete some of the records stored
in memory.
month, and day) settings.2.Hold down A until the flashing cursor () appears in
"The year can be set in the range of 2000 to 2039.
"The watchOs built-in full automatic calendar automatically makes allowances forthe text area of the display, which indicates the setting
screen.
different month lengths and leap years. Once you set the date, there should be noNumber area3.Use B and D to change the character at the cursor
reason to change it except after you have the watchOs battery replaced.
New Data screenposition in the text area. The character changes in the
following sequence.
To toggle between 12-hour and 24-hour timekeeping
While the Date/Time screen is on the display in the Timekeeping Mode, press B toPress .Press .
toggle between 12-hour and 24-hour timekeeping for the digital time.
"With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for(space)toto
times in the range of noon to 11:59 p.m. and no indicator appears to the left of the
hour digits for times in the range of midnight to 11:59 a.m.
"With the 24-hour format, times are displayed in the range of 0:00 to 23:59, with 24
indicator.
"The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is also
applied in all other modes. |