Module No. 2318/2319
GENERAL GUIDE
?Press BBBBB to change from mode to mode.
Calendar ModeTimekeeping ModeAlarm ModeDual Time Mode
CrownCrown
ABOUT THE BACKLIGHT (Module 2319 only)To set the hands
1.When the second hand is at 12 o'clock position, stop it by pulling the crown out.
?Hold down LLLLL to illuminate the display for about 2 seconds. The backlight is dis-2.Set the hands by turning the crown.
abled while an input screen (with a flashing setting) is on the display.3.Press the crown in on a time signal.
?The backlight of this watch employs an electro-luminescent (EL) light, which loses
its illuminating power after very long term use.
?Frequent use of the backlight shortens the battery life.
?The watch emits an audible sound whenever the display is illuminated. This does
not indicate malfunction of the watch.ALARM MODE
?The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
?The backlight automatically turns off whenever an alarm sounds.
A LN
CALENDAR MODEHourMinutes
?This is the normal mode for this watch.
To set the dateHour Minutes
When the Daily Alarm is turned on, an alarm sounds for 20 seconds at the preset
Hour hand Minute hand
time each day.
To set the Alarm Time
1.Hold down AAAAA until the ADJ indicator starts to flash, followed by flashing of the hour
CrownSecond handdigits of the alarm.
?The alarm turns on at this time.
2.Press BBBBB to increase the hour digits. Holding down BBBBB changes the digits at high
YearMonthDayspeed.
3.Press AAAAA to move the selection to the minutes digits.
4.Press BBBBB to increase the minutes digits. Holding down BBBBB changes the digits at high
DayDay of weekspeed.
1.Hold down AAAAA until the ADJ indicator starts to flash, followed by flashing of the year5.Press AAAAA to complete the procedure.
digits.?If you do not operate any button for a few minutes while a selection is flashing, the
2.Press BBBBB to increase the year digits. Holding down BBBBB changes the digits at highflashing stops and the watch goes back to the Alarm Mode automatically.
speed.
3.Press AAAAA to move the selection to month digits.To stop the alarm
4.Press BBBBB to increase the month digits. Holding down BBBBB changes the digits at high?Press any button to stop the alarm after it starts to sound.
speed.
5.Press AAAAA to move the selection to the day digits.To turn the Daily Alarm on and off
6.Press BBBBB to increase the day digits. Holding down BBBBB changes the digits at high
Press AAAAA while in the Alarm Mode to turn the Daily Alarm on and off.
speed.
7.Press AAAAA to complete the procedure.Press AAAAA.
?If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Calendar Mode automatically.
?The date can be set with the range of January 1,1995 to December 31, 2039.
?The day of the week changes automatically in accordance with the date.To test the alarm
Hold down BBBBB to sound the alarm.
TIMEKEEPING MODE
DUAL TIME MODE
?Use this mode to set the current time. An incorrect time setting will result in incor-
rect operation of the calendar.
Crown0
HourMinutes
SecondsHour
12/24MinutesHour Minutes
HourMinutes
Press AAAAA.To set the Dual Time
1.Hold down AAAAA until the ADJ indicator starts to flash, followed by flashing of the hour
digits.
2.Press BBBBB to increase the hour digits. Holding down BBBBB changes the digits at high
?Press AAAAA to switch the display between Hour/Minutesspeed.
Secondsand Seconds.3.Press AAAAA to move the selection to the minutes digits.
4.Press BBBBB to increase the minutes digits. Holding down BBBBB changes the digits at high
To set the timespeed.
1.Hold down AAAAA until the ADJ indicator starts to flash, followed by flashing of the5.Press AAAAA to complete the procedure.
seconds digits.?In the Dual Time Mode, the seconds count is not displayed. But it is synchronized
2.Press BBBBB to reset the seconds to 00. If you press BBBBB while the seconds count is inwith the seconds count of the Timekeeping Mode.
the range of 30 to 59, the seconds are reset to 00 and 1 is added to the minutes. If?If you do not operate any button for a few minutes while a selection is flashing, the
the seconds count is in the range of 00 to 29, the minutes count is unchanged.flashing stops and the watch goes back to the Dual Time Mode automatically.
3.Press AAAAA to move the selection to the hour digits.?The format(12-hour and 24-hour) of the Dual Time Mode matches the format you
4.Press BBBBB to increase the hour digits. Holding down BBBBB changes the hour digits atselect for normal timekeeping.
high speed.
5.Press AAAAA to move the selection to the minutes digits.
6.Press BBBBB to increase the minutes digits. Holding down BBBBB changes the minutes
digits at high speed.
7.Press AAAAA to move the selection to 12/24.
8.Press BBBBB to toggle the timekeeping format between 12-hour and 24-hour.
9.Press AAAAA to complete the procedure.
?If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Timekeeping Mode automatically. |
ACEC
