GFX2200HT GUITAR AMPLIFIER
The Front Panel:
LYLYCHO 1CHO 1CHO 2CHO 2
RTRTRYRY
REVREV N NOCTVOCTV
BLRBLRI-WI-WT-TAA-HHWWAAHH
LEVEL
1234567 89101112 1314151617 18 192021
. POWER:Use this switch to turn the ampli-10. MID: Use this control to adjust the19. GAIN ONE:Use this control to adjust the
er on (top of the switch depressed) and ofmidrange frequency level of Channel B.famount of light distortion for Channel A. Gain
bottom of the switch depressed).One produces less intense distortion than
11. LOW:Use this control to adjust the low
Gain Two (#17) and is active when the Gain
. ON LED:This LED illuminates when thefrequency level of Channel B.
switch (#18) is in the out position.
mplifier is turned on.
12. CHANNEL SELECT: Use this switch to
20. INPUTUse this 1/4� jack to connect your:
. CHANNEL SELECT FOOTSWITCH: In-select either channel. With the switch in the
guitar to the amplifier by means of a shielded
ert the 1/4� stereo plug on the cable attachedout position, Channel B is selected and the
instrument cable.
o the two-button footswitch (supplied) intoadjacent LED illuminates. When the switch is
his jack. This will allow you to use thedepressed, Channel A is selected.21. TUNER:The tuner is active whenever the
ootswitch to control channel and gain selec-amplifier is turned on. The bottom row of
CHANNEL A: The Overdrive Channel:
on (Channel A - see #18).LEDs correspond to the strings of your guitar.
13. LEVEL:Use this control to adjust the out-The top row of LEDs indicate which way you
. DSP FOOTSWITCH: Insert the 1/4� mono
put level of Channel A.need to adjust each string for proper tuning. A
lug on the cable attached to the two-button
string is properly tuned whenever the corre-
ootswitch (supplied) into this jack. 14. HIGH:This willUse this control to adjust the high
sponding LED on the bottom row and the LED
llow you to use the footswitch for on/offrequency level of Channel f con-A.
in the center of the top row are illuminated.
rol of the selected DSP effect.
(See detail below.)
15. MID: Use this control to adjust the
. DSP MODE: Use this control to select onemidrange frequency level of Channel A.
f the 16 built-in digital effects. A listing of the
"TUNED"
16. LOW:Use this control to adjust the low"FLAT""SHARP"
ffects is shown on page 3.
frequency level of Channel A.
. DSP LEVEL:Use this control to adjust the
17. GAIN TWO:Use this control to adjust the
mount of the digital effect. In its fully counter
amount of heavy distortion for Channel A.
lockwise position the signal will be Odry�
Gain Two produces more intense distortion
without any effect). As you rotate the control
than Gain One (#19) and is active when theSTRING INDICATORS
lockwise the amount of effect increases.
Gain switch (#18) is depressed.
CHANNEL B: The Clean Channel:
18. GAIN SELECT:Use this switch to select
. BRIGHTThis switch, when depressed,:one of the two gain controls for Channel A
oosts the upper frequencies of Channel B.(#17, #19). When the switch is depressed,
gain two is selected and gain one is disabled.
. LEVEL:Use this control to adjust the out-
Both of the adjacent LEDs will illuminate. With
ut level of Channel B.
the switch in the out position, gain one is
. HIGH:Use this control to adjust the highselected. The right-side LED will illuminate.
requency level of Channel B.When a footswitch (#3) is used, this switch is
disabled. The LEDs continue to function in the
manner described.
4 |