INSTALLATION
If the Auto Mower leaves the charging station before the
Installation, step by step
boundary wire has been installed completely, it will stop in front
of the charging station and alarm Osense no signal from the
The wires must be connected to the charging stationOs terminal
wire�. This alarm will stop automatically when the boundary wire
block, as shown in this wiring diagram, when steps 3-11 in
is connected. You can also switch off the Auto MowerOs alarm
these installations instructions are carried out.
by lifting the cover and entering the first digit of the code.
1
87 6 5 4 3 2 16. Install the boundary wire as set out in the description, see
2OInstallation of the boundary wire�. Wait to connect the cable
6
5ends.
435612
15 V7. Install the search wire as set out in the description OInstallation
535 09 65 - AX
of the search wire�. Wait to connect the cable ends.
Use the tool supplied to connect the six wires to the terminal
8. If the Auto Mower is in the charging station � fold up the cover,
block. See drawing.
enter the first digit of the code and move the mower from the
charging station.
9. Lay the boundary wires in the wire channels. Trim the wires,
strip the insulation and connect to terminals 2 and 5, as shown
in the wiring diagram on the left.
10. Lay one search wire in the wire channel, as shown in the wiring
diagram on the left, strip the insulation and connect to terminal
6.
11. Lay the other search wire in one of the four slots available at the
front of the charging station (see drawing on left). For most
installations one of the two wire channels on the left is most
suitable. Strip the wire and connect to terminal 1.
Now place the Auto Mower at right angles to the search wire, a
couple of metres from the charging station, and key in the
command * 31 #. Check whether the Auto MowerOs contact pins
line up roughly with the centres of the contact plates when it
docks with the charging station. If they are not aligned with the
contact plates then you should disconnect the incoming search
NOTE! Do not let any metal objects touch the chargingwire from terminal 1 and route it through one of the other wire
station contact plates while the transformer mains cablechannels. Repeat the docking operation three or four times to
is plugged into the power socket. This can cause theensure that the Auto Mower docks correctly with the charging
plates to short-circuit and the transformer fuse will trip.station each time.
There is no risk of harmful electric shock from the 15 V
If the Auto Mower stops immediately and gives three beeps
low-voltage supply.
when you key in the command * 31 #, and LED 4 flashes or
1. Select the placement for the charging station as set out inLED 6 glows steadily, then the wires have been connected
OPlaning the installation�.incorrectly. If this happens go back to steps 9 and 10 and check
that the installation is correct.
2. Position the charging station and secure it to the ground using
the six nails supplied. Both wheel plates must be installed12. Make sure the surface in front of the charging station is com-
beneath and in front of the charging station as shown in thepletely flat, so that both of the Auto MowerOs charging pins make
figure below. They prevent the occurrence of charging andgood contact with the charging stationOs contact plates. Adjust
docking problems as a result of soil compaction.the charging station vertically if necessary. See drawing below.
Test the boundary wire with the aid of the switch on the
charging station, see the figure below.
Y A continuous beep means that the search and
boundary wires are not broken.
Y An series of beeps means incorrect installation or a
3. Strip both conductors on the low-voltage cable and connect tobreak in the search or boundary wire. Ensure that the
positions 3 and 4 on the charging station terminal block. It doessearch and boundary wires have been laid in
not matter which of the conductors that are connected toaccordance with the installation instructions, or
terminals 3 and 4.repair the break in the wire.
Y If no beep is heard there is no power supply to the
4. Run the low voltage cable to the transformer. Insert the low
charging station.voltage cable connector in the transformer. Connect the
transformerOs mains cable to a 230 V wall socket.
5. As power is supplied to the charging station you can charge the
Auto Mower while the boundary wire and search wire are being
installed. Place the mower in the charging station with the ON/
STOP switch set to STOP for around 1 hour. Then lift the cover,
set the switch to ON, enter the code 0000 # and close the
*
cover. When the switch is set to STOP the battery is charged
using a very low current, which is kinder to the battery when it is
being charged for the first time.See also OCharging an empty
battery�. The first charge takes a few hours.
10 � English |
ACEC
