3. Editing
5. Rotate the knobs and the sound will change. The
3. Editingname display will indicate the name of the
parameter assigned to that knob, and the MAS-
In Play mode and Individual mode, you can edit eachTER/VALUE display will indicate the value. At this
effect, set noise reduction and program levels, andtime, the OORIG� icon will light when the position
modify the program name.of the knob matches the original value N i.e., the
During editing, the edit icon in the display will blink.value before you began editing.
Instead of the five value knobs, you can also use the
The parameter assigned
cursor switches(, ) to select parameters, and useto the knob you moved
the MASTER/VALUE switches ( , ) to adjust the
Edit iconValue of the parameter
value of the parameter currently shown in the name
display.
In Phrase Trainer mode, it is possible to edit the DRIVE-
AMP and CABINET effect blocks, but it is not possibIf you do not wish to use the DRIVE-AMPle to effect block,
perform editing operations that use the name display,
press the DRIVE-AMP effect block select switch until
MASTER/VALUE display, the cursor switches or the
MASTER/VALUE switches. In addition, it is not possibthe LED goes dark. The DRIVE-AMPle effect block is
to switch programs or effect channels.now bypassed, and the name display will indicate
O-OFF-.�
The cabinet effect can be edited in the same way as the
Editing effects
drive amp effect. Since the modulation, pedal, and
Rotate the effect select knob of the effect block that youambience effects do not have separate effect channels,
wish to edit, or press the corresponding effect blockbegin from step 2 of OEditing example.�
select switch. The effect block LED will begin blinking,
For some effects, it is not possible to simultaneously use
indicating that it has been selected for editing.
the MODULATION and PEDAL effect blocks, or the
Each program has two channels of settings (A and B)PEDAL and AMBIENCE effect blocks. If you attempt to
for the drive amp and cabinet effects. Press the effectturn on both effect blocks, the block that had been turned
channel switch to select the channel you wish to edit.on first will automatically be turned off.
Use the effect select knob, effect block select switch,
and value knobs to edit the settings.
Quick Editing for the DRIVE-AMP
If you wish to save the edited effect, perform the
effect block
OProgram write� operation. If you fail to do this, the effect
program will revert to its original settings when yIn the default state of each mode, the DRIVE-AMPou turn
off the power or select a different program.effect block parameters used by the selected program
are assigned to the value knobs (except when the effect
Editing example
is off).
As an example, we will explain how to select TUBE
When you rotate each value knob, the AX1500G will
OD as the drive amp effect for channel B.
enter edit mode (the effect program switch LED and
1. Press the effect channel switch to select channel Bthe edit icon will blink). The name display will show
(the channel LED will light red).the parameter name, the MASTER/VALUE display
will show the parameter value, and the sound will
2. If the name display indicated OTUBE OD � when
change.
you pressed the effect block select switch(DRIVE-
If you wish to change an effect that is in use, use the
AMP), simply continue. If not, turn the DRIVE-
effect select knobs to select the desired effect.
AMP effect select knob to the TUBE OD position. If
the effect select knob was already located at TUBEIt is not possible to edit when other functions are
assigned to the value knobs, when the AX1500G is
OD, first select a different effect model, and then
bypassed, muted, or recording in Phrase Trainer mode.
turn the knob back to TUBE OD.
3. The effect block LED will begin blinking, indicating
that it has been selected for editing. (The name
display will indicate the model name as OTUBE
OD .�) If you selected a programmed effect, the
OORIG� icon will light.
4. The five value LEDOs will light, and the correspond-
ing value knobs will be assigned to DRIVE,
LEVEL, TREBLE, MIDDLE, and BASS respec-
tively, and will function as knobs that adjust the
value of each parameter. (Refer to p.16, OEffect
parameters.�)
12 |