SwitchThe GREEN and WHITE cable leads are used to control an exter-
Built-in, leaf-type, non-locking, push-to-talknal relay or control circuit. Refer to the following table and to the
Shock Mountwiring diagram in Figure 4.
Internal rubber vibration isolator
CableWIRE FUNCTIONXLR1/4 IN.
COLORCONNECTORPHONE
Highly durable cable with effective hum shielding, four conduc-INPUT TYPEPLUG
tors (two shielded), plastic jacketed
REDAUDIOPIN 2TIP
Model 515SBGX: 1.8 m (70 in.)
Models 515SBG-18X and 515SBG-18XF: 1.3 m (51 in.) from
UNBALANCEDBLACKAUDIO GROUNDPIN 3SLEEVE
gooseneck
SHIELDCHASSIS GROUNDPIN 1SLEEVE
Case
Silver finish die casting with black enamel diecast grille andREDAUDIO +PIN 2TIP
stainless steel screen
BALANCEDBLACKAUDIO -PIN 3RING
Dimensions
See Figure 3 SHIELDCHASSIS GROUNDPIN 1SLEEVE
6.5 in.
16.5 cmDIRECTION TOACTUATE
SWITCH
CASE GROUND
51 in.
120 cm
0.85 in.
1.5 in.2cm
3.75 cm
RED DOTGREEN
OVERALL DIMENSIONSWHITE
FIGURE 3BLUE
CertificationBLACK
Conforms to European Union directives, eligible to bear CEREDCARTRIDGE
marking; meets European Union EMC Immunity Requirements
SHIELD
(EN 55103).
Net WeightINTERNAL CONNECTIONS
515SBGX ......................................................380 g (13.5 oz)FIGURE 4
515SBG-18X .................................................900 g (31.8 oz)MOUNTING THE 515SBG-18X AND 515SBG-18XF
515SBG-18XF...............................................787 g (27.8 oz)
Mount the 515SBG-18X or 515SBG-18XF as follows:
FURNISHED ACCESSORIES1. Thread the supplied hexnut all the way down on the mounting
1.27 mm (.050 in.) Hex Wrench ................................. 80A67flange.
45.75 cm (18 in.)Gooseneck 2. Thread the gooseneck tightly on the flange.
(515SBG-18X, 515SBG-18XF only)...............................G183. Back the hexnut up against the gooseneck, and use a wrench
Flange (515SBG-18X only) ....................................... A13HDto tighten the nut firmly against the bottom of the gooseneck.
Flange (515SBG-18XF only).......................................... A12
MOUNTING THE 515SBX ONTO A GOOSENECK
REPLACEMENT PARTSMount the 515SBGX onto a gooseneck or fixed pipe with a 5/8 in-
Cartridge....................................................................... R18027 thread as follows:
Grille Assembly .......................................................RK334G1. Unscrew the black end cap from the microphone.
Cable...................................................................... 70A40632. Remove the thin metal washer and the metal spacer.
Gooseneck (515SBG-18X, 515SBG-18XF) ...................G183. Re-install the washer by sliding it back onto the cable and up
Flange (515SBG-18X)............................................... A13HD
into the end of the microphone.
Flange (515SBG-18XF).................................................. A12
4. Slip the cable into the gooseneck or pipe and thread the
Windscreen ...............................................................A85WS
microphone firmly to the mount.
CONNECTIONSFor additional service or parts information, please contact Shure's
These low-impedance microphones are designed for connection to Service department at 1-800-516-2525. Outside the United States,
microphone inputs rated at 75 to 300 ohms. Using balanced-line please contact your authorized Shure Service Center.
low-impedance cables permits very long cable lengths without af-
fecting response or level. The RED and BLACK cable leads are the
microphone conductors for balanced-line connections; the shield is
connected to the amplifier ground.
For unbalanced operation, connect the BLACK lead to the shield,
and use the RED lead as the microphone conductor.SHURE Incorporated http://www.shure.com
United States, Canada, Latin America, Caribbean:
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.
Phone: 847-600-2000 U.S. Fax: 847-600-1212 Intl Fax: 847-600-6446
Europe, Middle East, Africa:
Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414
Asia, Pacific:
Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055
2 |