BassLink T OM 10/13/04 2:21 PM Page 8
TROUBLESHOOTINGSPECIFICATIONS
Y PROBLEM:Y PROBLEM:Y PROBLEM:Amplifier Power:250Wrms
POWER LED is not lit. No output from BassLink T when head-unit BassLink T produces a loud humming noise with
Frequency Response: 20Hz to 120Hz
fader control is set to front or rear.the system OFF when using speaker-level inputs.
CAUSES and SOLUTIONS:Fuse:30A
1. Fuse is blown and needs replacement.CAUSE and SOLUTION:CAUSE and SOLUTIONS:
Max. Current Draw:26A
2. Head unit is not functioning properly. CheckInput connections are improperly wired. Verify This problem is caused by a feedback loop
remote voltage, and power, ground or remoteall connections (see Applications, starting onbetween your speakers and the high-level inputsIdle Current Draw:< 800mA
connections.page 4).of BassLink T.
Input Sensitivity:50mV to 4V
Line-level input
Choose one of the following solutions:
Y PROBLEM:Y PROBLEM:1V to 16V
POWER LED is lit but there is no bass.BassLink T turns on before head unit is 1. Connect a wire from the REMOTE terminal onHigh-level input
completely on and produces a Othump� sound.BassLink T to the remote turn-on of your head
Crossover Frequency: 50Hz to 120Hz
CAUSES and SOLUTIONS:unit or to the vehicleOs accessory circuit. On the
1. Inputs are not connected. Check connections.CAUSE and SOLUTION:control panel, slide the AUTO-ON switch to theCrossover Slope:12dB per octave
2. Head-unit fader control is not set properly.For speaker-level connections, BassLink T isOFF position.
Bass Boost:�6dB to +3dB @ 40Hz
Adjust head-unit fader control to feed audioreceiving a false turn-on signal. On BassLink TOs
signals to BassLink T.top panel, slide AUTO TURN-ON to OFF and use2. Connect the supplied capacitors between Dimensions:
the Remote (REM) connection. each of the speaker outputs of the head unit(L x W x H)40-3/8" x 6-7/16" x 14-3/8"
and the speakerOs positive lead as shown (1026mm x 164mm x 366mm)
Y PROBLEM:in Figure 14. Connect each positive lead of
BassLink T sounds muddy or distorted.Y PROBLEM:BassLink TOs high-level inputs to the head-unit
BassLink TOs POWER LED remains on after headside of the capacitors. Use one capacitor per
CAUSES and SOLUTIONS:unit is turned off.speaker input channel.
1. Gain is set too high and PEAK LED is lit
constantly. Readjust GAIN control (see CAUSE and SOLUTION:Figure 14. Connecting supplied capacitors.
Tuning BassLink Ton page 7). For speaker-level connections, this is normal+ Speaker wire
2. Bass is set too high. Readjust BASS BOOSToperation when AUTO TURN-ON is set to ON.from head unitTo + speaker lead
Capacitor
control (see Tuning BassLinkT on page 7).BassLink T will remain on another 5 to 10 minutes
3. Head-unit output is distorted or blown. Seeafter sensing that audio signals are not present
your authorized Infinity car audio dealer.before shutting down.Declaration of Conformity
To + speaker-level
input on BassLink T
We, Harman Consumer International
2, route de Tours
72500 Chateau-du-Loir
France
declare in own responsibility that the product described in this
ownerOs manual is in compliance with technical standards:
EN 55013:2001
Infinity Systems, 250 Crossways Park Drive, Woodbury, NY 11797 USA EN 55020:2002
516.674.4INF (4463) Y FAX 516.682.3556 Y www.infinitysystems.comEmmanuel Millot
? 2004 Harman International Industries, IncorporatedHarman Consumer International
Part No. BASSLINKTOM Y 10/04Chateau-du-Loir, France 10/04 |
ACEC
HARMAN KARDON
