Identification of Controls
ConnectionsConnections
INTRODUCTION
Y There are a variety of ways to connect the DVD Recorder+VCR to your TV and other equipment. Use only one of
Rear panel
the connections described below. Whichever TV connection you use will work with all input sources.
Y Please refer to the manuals for your TV, VCR, stereo system, or other devices as necessary to make the best
connections.
!@#$%^Y For better sound reproduction, connect the DVD Recorder+VCROs AUDIO OUT jacks to the audio in jacks of your
amplifier, receiver, stereo, or audio/video equipment. See �Connecting an Amplifier/Receiver� on page 18.
CONNECTIONSCaution
DVD & VCR OUT
AUDIO OUTCOMPONENT OUT OUT LINE 2 ANT. INY Make sure the DVD Recorder+VCR is connected directly to the TV, and the TV is set to the correct video input.
R Pr R
AUDIOY Do not connect the DVD Recorder+VCROs AUDIO OUT jack to the phono in jack (record deck) of your audio system.
S-VIDEOOUTL PbL
COAXIALY Do not connect the DVD Recorder+VCR via your VCR. The DVD image could be distorted by the copy protection
AUDIO OUT DIGITAL Y VIDEO RF OUTsystem.
AntennaAntenna
Connecting Antenna/Cable
( *&Cable TV
Wall Jack
1Disconnect the antenna/cable from the rear of your
Flat Wire
TV. (300 ohm)
!AC Power Cord^RF IN (FROM ANT.)
2Connect this cable to the jack marked RF IN (FROM300/75 ohmOROR
Plug into a power outlet.Connect to your antenna or cable TV outlet.Adaptor
ANT.) on the rear panel of the DVD Recorder+VCR.(Not supplied)
@AUDIO OUT (L, R)&RF OUT (TO TV)
Connect to a TV or other equipment with audioConnect to a TV with an RF coaxial input.
inputs.*COAXIAL (Digital Audio Out)DVD & VCR OUT ANT. IN
AUDIO OUTCOMPONENT OUT OUT LINE 2
#COMPONENT/PROGRESSIVE VIDEO OUT (Y Pb Pr)Connect to an amplifier with a coaxial digital R Pr R
AUDIO
DEO
Connect to a TV with Component Video (Y Pb Pr)audio input.TL PbL
COAXIAL
inputs.(S-VIDEO OUT DIGITALAUDIO OUT Y VIDEO
RF OUT
$AV OUT (VIDEO, L-AUDIO-R)Connect to a TV with an S-Video Input.
Cable Service Without Cable Box
Rear of DVD Recorder+VCR
Connect to a TV with video and audio inputs.
If your cable wire is connected to your TV without a
%LINE2 (VIDEO, L-AUDIO-R)
converter or descrambler box, unscrew the wire from your TV and attach it to the RF IN (FROM ANT.) jack on the
Connect to the audio/video outputs of an external
rear panel of the DVD Recorder+VCR.
source (VCR, Camcorder, etc.).
Use the supplied coaxial cable to connect between the DVD Recorder+VCROs OUT (TO TV) jack and the antenna
input jack on your TV. With this connection, you can receive all midband, superband, and hyperband channels
Caution
(all cable channels).
Y Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage
to the DVD Recorder+VCR.Cable Service With Cable BoxCable TV
Wall Jack
If a cable box is required in your cable system, followBack Panel of
Typical Cable Box
the instructions shown at right. This hookup permits
both TV and DVD Recorder+VCR operation.
To view or record a CATV channel:
1Tune the TV to the correct video input channel.
2Set the DVD Recorder+VCR to the output channel of
DVD & VCR OUT
the cable box using the [CH &/ ] or the [0-9] keys AUDIO OUTCOMPONENT OUT OUT LINE 2 ANT. IN
Pr
on your DVD Recorder+VCR (e.g., CH3). R R
AUDIO
TEOL PbL
3Select the channel you wish to view on the cable COAXIAL
DIGITAL Y VIDEO
box.AUDIO OUT RF OUT
Rear of DVD Recorder+VCR
Y If you are using a cable box to tune channels, it is not necessary to run Auto Channel Search as indicated on page
23.
1415 |
ACEC
DAEWOO
