Filling with saltRinse aid
Rinse aid is automatically added during the last rinse,
Special salt can be added in one of two ways:ensuring thorough rinsing, and spot and streak free drying.
The dispenser, which is positioned inside the door, holds
If you are using dishwasher detergent that already
about 110 ml of rinse aid, which is sufficient for 16 - 40
contains salt, the detergent including the salt is placed in
dishwashing programmes, depending upon the dosage
the detergent compartment.
setting.
- In this case the water softener must manually be set to 1
and electronically to 1 to ensure that the special salt is
taken from the detergent container only.
Rinse aid can be added in one of two ways:
If you are using dishwasher detergent and salt separately If you , are using dishwasher detergent that already
the special salt is to be put into the salt containercontains .rinse aid, the detergent including the rinse aid is
- In this case the water softener must manually be placed set to in 1 the detergent compartment.
or 2 and electronically between 1 and 5 (depending - In on this case the rinse aid compartment must be empty
the water hardness in your area) to ensure that the and the rinse aid indicator light deactivated.
special salt is taken from the salt container only.If in the rinse aid dispenser there is still rinse aid you
must wait until it has finished before using detergent that
contains rinse aid.
Only use salt specifically designed for use in
If you are using dishwasher detergent and rinse aid
dishwashers.
separately, the rinse aid is to be put into the rinse aid
All other types of salt not specifically designed for use in
dispenser.
a dishwasher, especially table salt, will damage the water
- In this case the rinse aid dosage must be set in position
softener.
from 1 to 6 (see "Adjusting the dose") and the rinse aid
Only fill with salt just before starting one of the washing
indicator light activated.
programmes.
This will prevent any grains of salt or salty water, which
may have been spilt, remaining on the bottom of the
machine for any period of time, which may cause
Filling with rinse aid
corrosion.
(Rinse aid dispenser type A)
To fill:1.Open the container by pressing the release button (A).
1.Open the door, remove the lower basket and unscrew 2.Fill the with rinse aid exactly up to the level marked "MAX".
cap of the salt container by turning it anticlockwise.
2.Pour 1 litre of water inside the this container is necessary (
only before filling with salt for the ). first time
3.Using the funnel provided,
pour in the salt until the
SALE
container is full.
SALT
SALZ
4.Replace the cap making SEL
sure that there is no trace
of salt on the screw
thread or on the gasket.BR07BR08
5.Screw on the cap tightly
Ensure that the lid is closed after every refill.
turning it clockwise until it
stops with a click.SR14
The salt container will require topping up periodicallyAdjusting . You arethe dose
reminded of this by the salt indicator light on the control panel
According to the finish and drying results obtained, adjust the
which comes on when the salt has finished.
dose of rinse aid by means of the 6 position selector (position
Do not worry if water over flows from the unit when 1 filling minimum withdosage, position 6 maximum dosage).
salt, this is quite normal.
Increase the dose if there are drops of water or lime spots on
The salt indicator light on the control panel can remainthe dishes after washing.
illuminated for 2-6 hours after the salt has been
The dose is factory set in position 4.
replenished, assuming the dishwasher remains switched
Reduce it if there are
on. If you are using salts that take longer to dissolve then
sticky whitish streaks on
this can take longer. The function of the machine is not
the dishes.
affected.
BR09
23 |
ACEC
ZANUSSI
