The operating instructions mentioned here are partial abstracts
SECTION 1from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remein as in the manual.
GENERAL
Getting StartedGetting startedGetting StartedGetting Started
Use of the Tilt-Swivel
PrecautionsIdentifying Parts and Controls
This monitor can be adjusted within the angles shownSee the pages in parentheses for further details.
Installationbelow. To find the center of the monitorOs turning radius,
align the center of the monitorOs screen with the centeringFront
Rear
Y Prevent internal heat build-up by allowing adequate airdots on the stand.
circulation. Do not place the monitor on surfaces (rugs,Hold the monitor at the bottom with both hands when you
blankets, etc.) or near materials (curtains, draperies) thatturn it horizontally or vertically. Be careful not to pinch
may block the ventilation holes.your fingers at the back of the monitor when you tilt the
Y Do not install the monitor near heat sources such asmonitor up vertically.
radiators or air ducts, or in a place subject to direct
sunlight, excessive dust, mechanical vibration, or shock.
Y Do not place the monitor near equipment which generates
15°
magnetism, such as a transformer or high voltage power90°
lines.
90°
Maintenance5°
1-1Y Clean the cabinet, panel and controls with a soft cloth
lightly moistened with a mild detergent solution. Do not
use any type of abrasive pad, scouring powder, or
Centering dots
solvent, such as alcohol or benzine.1 ? (reset) button (page 13)6 AC IN connector (page 4)
Y Do not rub, touch, or tap the surface of the screen withEN
NoteResets the adjustments to the factory settings.Provides AC power to the monitor.
sharp or abrasive items such as a ballpoint pen or
Do not remove the tilt-swivel base from the monitor.
screwdriver. This type of contact may result in a scratched2 ? (brightness) down and up (./>) buttons7 Video input connector (HD15) (page 4)F
picture tube.(pages 5 � 13)Inputs RGB video signals (0.700 Vp-p, positive) and
Y Clean the screen with a soft cloth. If you use a glassWarning on power connectionAdjust the picture brightness.SYNC signals.ES
cleaning liquid, do not use any type of cleaner containing
Function as the (./>) buttons when adjusting other
an anti-static solution or similar additive as this mayY Use an appropriate power cord for your local power1 2 3 4 5C
items.
scratch the screenOs coating.supply.6 7 89 10
3 (menu) button (pages 5 � 13, 15)11 12 13 14 15
Examples of plug types:TransportationDisplays the MENU OSD.
4 > (contrast) left and right (?//) buttonsPin No.SignalPin No.Signal
When you transport this monitor for repair or shipment, use
(pages 5 � 13, 18)1Red8Blue Ground
the original carton and packing materials.
Adjust the contrast.2Green9N
for 200 to 240 V ACfor 240 V AC onlyFunction as the (?//) buttons when adjusting other(Sync on Green)10Ground
items.3Blue11ID (Ground)
Y Before disconnecting the power cord, wait at least 30
4ID (Ground)
seconds after turning off the power to allow the static5 u (power) switch and indicator (pages 14,12Bi-Directional
electricity on the CRT display surface to discharge.18)5DDC Ground*Data (SDA)*
Y After the power has been turned on, the CRT isTurns the monitor on or off.6Red Ground13H. Sync
demagnetized (degaussed) for about 5 seconds. ThisThe power indicator lights up in green when the7Green Ground14V. Sync
generates a strong magnetic field around the metal frame,monitor is turned on, and either flashes in green and
15Data Clock(SCL)*
which may affect the data stored on magnetic tapes andorange, or lights up in orange when the monitor is in
disks near the bezel. Place magnetic recording equipment,power saving mode.* Display Data Channel (DDC) Standard of VESA
tapes, and disks away from this monitor.
The equipment should be installed near an easily
accessible electrical outlet.
23 |