Module No. 1966/21441966/2144-1
GENERAL GUIDE
?Press CCCCC to change from mode to mode.
?After you perform an operation in any mode, pressing CCCCC returns to the Timekeeping Mode.
?If you do not press any button for a few minutes while making settings in any mode (indicated when settings are flashing), the watch automatically clears the setting screen (settings stop
flashing) and returns to the normal display for the mode you are in.
?This watch returns to the Timekeeping Mode whenever you hold down the CCCCC button for one or two seconds. If you ever lose track of what mode you are in or what you should do next,
hold down CCCCC to return to normal timekeeping.
?In any mode press LLLLL to illuminate the display.
Timekeeping ModeCountdown Alarm ModeStopwatch ModeAlarm ModeDual Time Mode
TIMEKEEPING MODETo switch the auto light switch function on and off
In the Timekeeping Mode, hold down BBBBB for one or two seconds to turn the auto light
Day ofMonthTo set the time and dateswitch function on and off.
week1.Hold down AAAAA while in the Timekeeping Mode until the
Day
seconds digits flash on the display because they areAuto light switch
selected.indicator
2.Press CCCCC to change the selection in the following se-
quence.
Hold down BBBBB
SecondsHourMinutes
ONOFF
12/24-Hour Format?The auto light switch indicator is shown on the display in all modes while the auto light
switch function is on.
Seconds?In order to protect against running down the battery, the auto light switch function is
Hourautomatically turned off approximately three hours after you turn it on. Repeat the
Day of weekDayMonth
Minutesabove procedure to turn the auto light switch function back on if you want.
PM indicator?Pressing LLLLL while in the Timekeeping Mode illuminates the display, regardless of the
auto light switchOs on/off setting.
3.While the seconds digits are selected (flashing), press DDDDD to reset the seconds to
00. If you press DDDDD while the seconds count is in the range of 30 to 59, the secondsCaution
are reset to 00 and 1 is added to the minutes. If the seconds count is in the range?The backlight of this watch employs an electro-luminescent (EL) light, which loses
of 00 to 29, the minutes count is unchanged.its illuminating power after very long term use.
4.While any other digits (beside seconds) are selected (flashing), press DDDDD to in-?Frequent use of the backlight shortens the battery life.
crease the number or BBBBB to decrease it. While the 12/24-hour format setting is?The watch emits an audible sound whenever the display is illuminated. This is
selected, press DDDDD or BBBBB to toggle it between 12 and 24. While the day of the weekbecause the EL light vibrates slightly when lit. It does not indicate malfunction of the
is selected (flashing), press DDDDD to advance to the next day or BBBBB to return to thewatch.
previous day.
Warning!
?Except for when adjusting the seconds or setting the 12/24-hour format, holding?Never try to read your watch when mountain climbing or hiking in areas that are
down a button changes the current selection at high speed.dark or in areas with poor footing. Doing so is dangerous and can result in
?When the 12-hour format is selected, the indicator P appears on the display toserious personal injury.
indicate OP.M.� times. There is no indicator for OA.M.� times.?Never try to read your watch when running where there is the danger of
?When the 24-hour format is selected, the indicator 24 appears on the display.accidents, especially in locations where there might be vehicular or pedestrian
5.After you set the time and date, press AAAAA to return to the Timekeeping Mode.traffic. Doing so is dangerous and can result in serious personal injury.
?Never try to read your watch when riding on a bicycle or when operating a
motorcycle or any other motor vehicle. Doing so is dangerous and can result
in a traffic accident and serious personal injury.
?When you are wearing the watch, make sure that its auto light switch function
ABOUT THE BACKLIGHTis turned off before riding on a bicycle or operating a motorcycle or any other
motor vehicle.
About the Auto Light Switch FunctionSudden and unintended operation of the auto light switch can create a
When the auto light switch function is turned on, the backlight automatically turns ondistraction, which can result in a traffic accident and serious personal injury.
for two seconds under the conditions described below. Avoid wearing the watch on the
inside of your wrist. Doing so causes the auto light switch to operate when not needed,
which shortens battery life.
Moving the watch to a position that is parallel to the ground and then tilting itCOUNTDOWN ALARM MODE
towards you approximately 40 degrees causes the backlight to illuminate.
Current timeThe countdown alarm can be set within a range of 1 sec-
ond to 24 hours. When the countdown reaches zero, an
ProgressAuto repeat
on indicatoralarm sounds for 10 seconds or until you press any but-beeper on
indicatorton.
Parallel to ground40°
To set the countdown start time
1.Hold down AAAAA while in the Countdown Alarm Mode. The
hours digits flash on the display because they are se-
lected.
?The backlight may not illuminate if the face of the watch is more than 15 degrees off2.Press CCCCC to change the selection in the following se-
parallel to the left or right. Make sure that the back of your hand is parallel to thequence.
ground.
Parallel to ground More than 15 degrees tooMore than 15 degreesHourMinutesSeconds
hightoo lowMinutes1/10
Mode indicatorSeconds
Seconds
3.Press DDDDD to increase the selected number or BBBBB to decrease it. Holding down either
button changes the selection at high speed.
?Press DDDDD and BBBBB at the same time to clear the starting time to 0:00' 00".
?Static electricity or magnetic force can interfere with proper operation of the auto
?To set the starting value of the countdown time to 24 hours, set 0:00' 00".
backlight function. If the auto backlight does not illuminate, try moving the watch backAA
to the starting position (parallel with the ground) and then tilt it back toward you again.4.After you set the countdown start time, press AAA twice to return to the Countdown
Alarm Mode.
If this does not work, drop your arm all the way down so it hangs at your side, and
then bring it back up again.
?Under certain conditions the backlight may not light until about one second or lessTo use the countdown alarm
after turning the face of the watch towards you. This does not necessarily indicate1.Press DDDDD while in the Countdown Alarm Mode to start the countdown alarm.
malfunction of the backlight.2.Press DDDDD again to stop the countdown alarm.
?You can resume countdown alarm operation by pressing DDDDD.
3.Stop the countdown alarm and then press BBBBB to reset the countdown time to its
starting value.
?When the end of the countdown is reached and auto repeat timing is off, the alarm
sounds for 10 seconds or until you stop the alarm by pressing any button. Count-
down timing stops and the countdown time is automatically reset to its starting
value after the alarm stops. |
ACEC
