? install an electric socket (or connection point) with a bipolar switch, having contacts with an opening Before using for the first time, ensure that all the points in the previous paragraphs have been complied
with concerning installation of the hood.
of at least 3 mms;
? if it is intended to install the hood with a plug, and the feed cable is not provided with one, a MOREOVER remember:
standard plug must be purchased. This plug be easily accessible;
? always turn off the main voltage supply by means of the bipolar switch before connecting and switch ? not to cook ?flambé? dishes, avoid flames directly underneath the hood;
on again only when connections have been completed, tested and are safe. ? to avoid leaving on any hot plates which generate strong free flames underneath the hood;
? to avoid any strong flames being issued from under saucepans at the sides;
5.4 CONNECTION TO THE POWER SUPPLY ? when frying, not to allow oil to splash or overheat in the pan, as this is a fire risk;
? before any cleaning or maintenance operation, disconnect the hood from the mains supply,
The flexible feed cable supplied is already connected internally and emerges from the hood near the air by means of the main switch or the bipolar switch or by removing the plug;
outlet duct. ? if other gas equipment or equipment which consumes ox ygen from the environment is
It is possible to effect two types of electric installation: used, ventilation must be sufficient. For safe ventilation, maximum depression in the room
? fixed installation; should not exceed 4 Pa (0,04 mbar) and there must be a hole on the outside facing wall
? installation by means of plug on a socket. (suitably positioned and dimensioned);
In both cases connection to the power supply must be carried out only by qualified personnel and in ? never use the hood without the aluminium filters;
conformity with national and international standards, in order to guarantee electric safety, using ? keep the aluminium filters clean, taking into account the recommended cleaning
suggestions (see MAINTENANCE par.);
standard materials.
? replace the carbon filters (if the hood is used as a filtering hood), as indicated;
? turn on the hood motor before you start cooking;
5.5 PRECAUTIONS TO BE TAKEN IF REPAIRS ARE TO BE CARRIED OUT ? turn off the hood motor about 10 minutes after you have finished cooking.
Repairs, including the replacement of the feed cable if necessary, are to be carried out only by qualified
personnel, using standard methods, instruments and materials. Any repairs carried out by others could 8 POSITION OF THE CONTROLS
prove to be dangerous and could be a fire risk.
In the SLIDER version ( SEE FIG.9) there are two slide switches;
6 MOUNTING OF THE DECORATIVE CHIMNEY
Motor control switch :
III motor ON switch: maximum speed;
The mounting of the decorative chimney is necessary both in the filtering and suction versions. For the II motor ON switch: intermediate speed;
filtering versions, a chimney with holes and deflector is available (SEE ACCESSORIES). I motor ON switch: minimum speed;
The decorative chimney is illustrated in FIG 7: it is made up of two parts which slide one into the other. O motor OFF switch: to switch the motor off.
Before mounting the chimney, you should fit the support bracket to the ceiling, as indicated at par. (4.4). Light control switch ( ):
To mount the chimney, proceed as follows: I switch ON: lights on;
? the two parts of the chimney are mounted as in FIG.7; O switch OFF: lights off.
? the chimney fixing screws are in the plastic bag supplied (small screws);
? position the base of the chimney with the holes in alignment with the hood holes; In the PUSH BUTTON control version (SEE FIG. 10), the controls are on the front of the hood:
? insert the small screws on the base of the hood and tighten them; III motor ON: switch maximum speed;
? slide the telescopic part of the chimney upwards until it touches the ceiling where the support II motor ON: switch intermediate speed;
bracket is positioned; I motor ON: switch minimum speed;
? insert the screws on the ceiling support bracket and tighten them. O motor OFF: switch: allows you to turn the motor off;
to switch the lamps on or off.
7 INSTRUCTIONS FOR USE and PRECAUTIONS |
ACEC
