To fix the bracket, proceed as follows:
3 MOUNTING INSTRUCTIONS
" decide exactly where on the ceiling (or on the wall), the support bracket for the chimney is to
3.1 DISMANTLING AND RE-POSITIONING OF THE GREASE FILTERS be fitted;
To mount the hood or insert the carbon filters, it is necessary to gain access to the inside,
therefore the grease filters should be removed. " make support and safety fixing holes with a drill;
" fit the screw plugs in the holes;
Attention: some cooker hoods are equipped with blind grease filters for side suction that cover the
real grease filters; in these cases before removing the grease filters it is necessary to take away " fit the screws in the plateholes and in the plugs;
" tighten the screws with a screwdriver.
the blind filters by gripping them from the side and pulling them downwards. (Fig. 5).
TO EXTRACT a grease-filter (see direction of arrow in FIG. 5): 3.3.2 FIXING TO THE WALL
To fix the hood to the wall, proceed as follows:
" pull the lever and take the grease filter out pulling it downwards.
TO RE-POSITION the grease-filter (SEE FIG. 5 opposite direction to the arrow): " based on the technical drawing, mark the position of the support and safety fixing holes on the
wall with a pencil, in such a way that the base of the hood is at the distance from the cooker
" insert the back side of the grease filter into its groove;
" pull the lever downwards and insert the front part of the filter; hob, as indicated in par. (2.1) and that it is horizontal. Mark the position of the holes with a
pencil making a small cross on the wall.
" release the lever and make sure that the pin of the handle enters into its hole.
" drill the support and safety fixing holes in the positions marked;
" fit the metal hooks to the support holes (see FIG.8) complete with plug and screws,
3.2 FITTING AND REMOVAL OF EVENTUAL CARBON FILTERS completely inserting the plastic plug and keeping the curved part on the outside and facing
If you wish to use the hood as a filtering hood, it is necessary to fit the carbon filters.
The carbon filters which contain activated carbon ARE OPTIONAL, and can be bought separately. downwards; in the safety fixing holes only insert the plastic plug;
" tighten the support screws;
We have 2 different kinds of carbon filters. Once you have dismantled them, it is possible to
recognize the kind of filter used in the hood (see FIG. 6). " rest the back of the hood on the wall and insert the hooks into the corresponding slots;
In case the mounted filter is the one shown in FIG. 6a, follow the following procedure for " make sure the hood is stable;
mounting: " holding the cross notched screwdriver in your hand; slowly tighten the horizontal alignment
" pay attention to the shape of the joints; screws one at a time, until the hood is perfectly horizontal above the cooker hob. The use of a
" insert the back side into its groove; level will help in this operation;
" insert the screws into the safety holes;
" lift the front side of the carbon filter, until it is blocked in position;
" clamp the filter by rotating the 2 knobs at 90°. " tighten the safety holes with the screwdriver.
3.3.3 MOUNTING OF THE SCAVENGING PIPE
To remove a carbon filter proceed as follows: (see FIG. 6A, opposite direction of arrows):
" rotate the two knobs at 90°; If the hood is to be used as a suction hood, to apply the pipe proceed as follows:
" measure the distance to be covered by the pipe and obtain parts of the right size;
" pull the front side of the filters downwards;
" fully extract, by removing the back of the filter from the groove. " insert the hood outlet mouthpiece into the pipe and block it;
" connect the lengths of pipe up to the hole towards the outside;
In case the carbon filters used are the ones shown in Fig. 6b, (pair of filters), proceed as
follows for mounting: " connect the pipe to the end which goes outside;
" make electrical connection (see par.4).
" grip the external part of the filter (the convex one);
" lay the filter on the side of the motor so that the joints in alu can enter the grooves; 3.3.4 MOUNTING OF THE DECORATIVE CHIMNEY
The decorative chimney shown in FIG. 7 is composed of 2 parts of metal sheet which slide one
" rotate the filter 60 ° in the direction shown by the arrow;
" to be sure that the filter is correctly installed, try to move this from the motor to the outside. If inside the other. To mount the chimney please proceed as follows:
" the 2 parts of the chimney are mounted as shown in FIG. 7;
it does not move, it means it has been correctly fitted.
Repeat the above for the other filter " position the base part of the chimney with holes matching the ones on the hood;
To remove both carbon filters proceed as follows for both of them (see FIG.6b, DIRECTION " insert small screws on the bottom of the chimey and fix them;
OPPOSITE TO THE ARROW): " let the telescopic part of the chimney slide to the height necessary to touch the ceiling and
" grasp the external part of the filter; come into contact with the chimney bracket;
" rotate the filter 60° in the direction opposite to the one shown in the picture, the carbon filter " tighten the screws on the chimney bracket to the ceiling.
will release the joint in alu; 3.4 MOUNTING THE ISLAND COOKER HOOD WITH EXTERNAL CHIMNEY
" grasp the filter and pull this far from its housing; The island cooker hood is intended to be mounted either directly on the kitchen ceiling or onto a
" repeat the above for the other filter. stable suspended false ceiling structure.
Check that the minimum distance between the bottom of the hood and the upper part of the hob
If you have a wall cooker hood (FIG.7), see par. 3.3. is in conformity with indications in par. 2.1.
If you have a island cooker hood with external chimney (FIG.10), see par 3.4. " Mark the centre of the position on the ceiling at which the hood will be mounted;
" according to the technical drawing, mark on the ceiling the position of the fixing points;
3.3 MOUNTING THE HOOD TO THE WALL " using a drill suitable for building materials, make the fixing holes and insert plugs so that they
3.3.1 PREPARATION OF THE DECORATIVE CHIMNEY ATTACHMENTS are flush with the ceiling;
To mount the decorative chimney, it is necessary to arrange for a ceiling attachment. " Mount the support structure to the ceiling FIG.9;
The support bracket is of such a shape that it can be fixed to the ceiling or the side wall (SEE " Fix the upper chimney to the support structure FIG.10, by means of 2 screws;
FIG. 7). |
ACEC
