ROLAND AR-200 Instruction Manual

AR-200_e.book 58 Z
8
?
?
?
??
?e
?
?xýe
Uxý9=
?p
?
? 
MIDI Implementation
Model: AR-200/3000 (Audio Recorder)I Program Change
Date: Nov.1,2000StatusSecond
Version: 1.00
CnHppH
1. Receive data (Media Player Section)n = MIDI Channel No. : 0H - FH (ch.1 - ch.16)
pp = Program number : 00H - 05H (prog.1 - prog.6)
 Channel Voice Message : 06H - 0AH (prog.7 - prog.11) *Only AR-3000
I Note Off : 14H - 1DH (prog.21 - prog.11)
StatusSecondThird : 46H - 4FHH (prog.71- prog.80)
8nHkkHvvH : 7FH (prog.128)
9nHkkH00H* This switches the MIDI note map used for the phrase assignments.
n = MIDI Channel No. : 0H - FH (ch.1 - ch.16)* The change goes into effect with the first new Note On after the Program Change is
kk = Note No. : 00H - 7FH (0 - 127)received. This has no effect on phrases being played before the Program Change is
vv = Velocity : 00H - 7FH (1 - 127)received.
* This stops playback of the phrase for the corresponding note number. (For more on the* Data is not received if the MIDI Receive channel setting is OFF. When set to 1-16, data is
corresponding phrases, refer to the Note On parameter.)received only on the selected channel. When set to ALL, data is received on all channels.
* This is ignored when "Trigger" is selected for MIDI Trigger Mode.
* The Note Off Velocity value is ignored.  System Common Message
* Data is not received if the MIDI Receive channel setting is OFF. When set to 1-16, data is
I Quarter Frame Messages
received only on the selected channel. When set to ALL, data is received on all channels.
* Data is received when Sync Source is set to "MTC." When the Quarter Frame message is
I Note Onreceived, operation proceeds with the start of the song synchronized to
StatusSecondThird
"00h00m00s00f00" with the "MTC Offset" and the "Delay Time" added.
9nHkkHvvH
* This acts upon the currently selected audio phrase.
n = MIDI Channel No. : 0H - FH (ch.1 - ch.16)* MIDI phrases and pattern phrases are ignored when Dual Mono mode is selected.
kk = Note No. : 00H - 7FH (0 - 127)
vv = Velocity : 01H - 7FH (1 - 127)StatusSecond
* This plays back the phrase for the corresponding note number.
F1HmmH (= 0nnndddd)
* With Program Change 1 (normally turning the power on), all note numbers (128nnn = Message type: 0 = Frame count LS nibble
numbers) are received. Corresponding phrase numbers may be selected freely.
1 = Frame count MS nibble
* With Program Changes 21-30, only Note Numbers 00H-63H (0-99) are received. The2 = Seconds count LS nibble
phrase numbers correspond to 1-1000 on Card A. Phrase assignments cannot be3 = Seconds count MS nibble
changed.
4 = Minutes count LS nibble
* With Program Changes 71 through 80, only Note Numbers 00H through 63H (0 through5 = Minutes count MS nibble
99) are received. The phrase numbers correspond to 1 through 1,000 on Card B (AR-3000
6 = Hours count LS nibble
only). Phrase assignments cannot be changed.7 = Hours count MS nibble
* With Program Changes 2-6 and 7-11, only Note Numbers 00H-63H (0-99) are received.
dddd = 4 bit nibble data : 0h - FH (0 - 15)
The phrase numbers correspond to 1-500 on Card A and 1-500 on Card B (AR-3000 only)Bit Field is assigned as follws.
respectively. Phrase assignments (AR-2000 compatible) cannot be changed.
Frame Countxxxyyyyy
* With Program 128, playback of the phrase in progress is stopped, regardless of the note
xxx Reserved (000)
number.yyyyy Frame No.(0-29)
* Data is not received if the MIDI Receive channel setting is "OFF." When set to 1-16, data
Seconds Countxxyyyyyy
is received only on the selected channel. When set to ALL, data is received on allxx Reserved (00)
channels.
yyyyyy Seconds (0-59)
* The Note On Velocity value changes the playback master volume.Minutes Countxxyyyyyy
* The Note On Velocity value is ignored in Dual Mono mode and MIDI playback.
xx Reserved (00)
* The Note On Velocity value is ignored when Note On Velocity is set to "Off."yyyyyy Minutes (0-59)
I Control ChangeHours Countxyyzzzzz
M Panpot (Controller number 10)x Reserved (0)
StatusSecondThirdyy Time Code type
BnHOAHvvH0 = 24 Frames / Sec
n = MIDI Channel No. : 0H - FH (ch.1 - ch.16)1 = 25 Frames / Sec
vv = Panpot : 00H - 7FH (0 - 127)2 = 30 Frames / Sec (Drop Frame)
(0-64-127)3 = 30 Frames / Sec (Non Drop Frame
default value = 40H(64)zzzzz Hours (0-23)
* This is adjustable in 127 steps, with 0 being full left, 64 center, and 127 full right.  System Exclusive Message
* When Panpot is off, this is not received.
StatusData BytesStatus
* When MIDI playback is conducted in Dual Mono mode, this is not received.F0H iiH, ddH,.., eeHF7H
* Data is not received if the MIDI Receive channel setting is "OFF." When set to 1-16, data
FOH:System Exclusive Message status
is received only on the selected channel. When set to ALL, data is received on alliiH ID Number:an ID number (manufacturer ID) to indicate the manufacturer whose
channels.Exclusive message this is. Roland's manufacturer ID is 41H.
ID numbers 7EH and 7FH are extensions of the MIDI standaerd; Universal Non-Real time
M Expression (Controller number 11)Messages (7EH) and Universal Real time Messages (7FH).
statusSecondThird: :
BnH0BHvvHdd,.., ee = Data :00H-7FH (0-127)
n = MIDI Channel No. : 0H - FH (ch.1 - ch.16)F7H :EOX (End of Exclusive Message)
vv = Expression : 00H - 7FH (0 - 127)
default value = 7FH (127)The system Exclusive Messages recived by the AR-200/3000 are; Data Set (DT1).
* This changes the volume level during playback of a phrase.Regarding the Data Set (DT1), please refer to "exclusive Communication".
* When Expression is off, this is not received.
* When MIDI playback is conducted in Dual Mono mode, this is not received.
* Data is not received if the MIDI Receive channel setting is "OFF." When set to 1-16, data
is received only on the selected channel. When set to ALL, data is received on all
channels.
58