8. H. Position Adjustment10. V. Position Adjustment
Purpose: To obtain correct horizontal position of Purpose: To obtain correct vertical width of screen
screen image.image.
Symptom of Misadjustment: If H. Position is Symptom of misadjustment: If V. Position is
incorrect, horizontal position of image on the screen incorrect, vertical height of image on the screen may
may not be properly displayed.not be properly displayed.
Test PointAdj. PointModeInputTest PointAdj. PointModeInput
[CH o / p] [CH o / p]
---RFMonoscope---RFMonoscope
buttonsbuttons
TapeM. EQ.Spec.TapeM. EQ.Spec.
---Monoscope90?5%---MonoscopeSee below.
Note: Use service remote control unitNote: Use service remote control unit
1. Operate the unit for at least 20 minutes.
1. Operate the unit for at least 20 minutes.
2. Enter the Service mode. (See page 5-1.)
2. Enter the Service mode. (See page 5-1.)
3. Receive the monoscope pattern.
3. Receive the monoscope pattern.
4. Press [9] button on the service remote control unit
4. Press [8] button on the remote control unit. ?H-P?
and select ?V-P? mode. (Display change ?V-S? and
is indicated.
?V-P? cyclically when [9] button is pressed).
5. Press [CH o / p] buttons on the service remote
5. Press [CH o / p] buttons on the service remote
control unit so that the monoscope pattern will be
control unit so that the top and bottom of the
90?5% of display size and the circle is round.
monoscope pattern will be equal of each other.
6. Turn the power off and on again. (Main power
6. Turn the power off and on again. (Main power
button on the TV unit.)
button on the TV unit.)
9. V. Size Adjustment11. U-Pedestal Adjustment
Purpose: To obtain correct vertical width of screen (6427FF only)
image.
1. In VIDEO mode of V1, V2, or YUV, press [3] button
Symptom of Misadjustment: If V. Size is incorrect, on the service remote control unit and select ?U-
vertical size of image on the screen may not be PED? mode. (Display changes ?U-PED? and ?V-
properly displayed.PED? cyclically when [3] button is pressed).
2. Switch the VIDEO mode to YUV. (Refer to "Initial
Test PointAdj. PointModeInput
Setting" on page 5-2)
[CH o / p] 3. To select one appropriate value in ?0? to ?15,?
---RFMonoscope
buttonspress [CH o / p] buttons on the remote control
unit.
TapeM. EQ.Spec.
4. Switch the VIDEO mode to previous mode.
---Monoscope90?5%5. Turn the power off and on again. (Main power
button on the TV unit.)
Note: Use service remote control unit.
1. Operate the unit for at least 20 minutes.12. V-Pedestal Adjustment
2. Enter the Service mode. (See page 5-1.)(6427FF only)
3. Receive the monoscope pattern.
1. In VIDEO mode of V1, V2, or YUV, press [3] button
4. Press [9] button on the service remote control unit on the service remote control unit and select ?V-
and select ?V-S? mode. (Display changes ?V-S? PED? mode. (Display changes ?U-PED? and ?V-
and ?V-P? cyclically when [9] button is pressed).PED? cyclically when [3] button is pressed).
5. Press [CH o / p] buttons on the service remote 2. Switch the VIDEO mode to YUV. (Refer to "Initial
control unit so that the monoscope pattern will be Setting" on page 5-2)
90?5% of display size and the circle is round.3. To select one appropriate value in ?0? to ?15,?
6. Turn the power off and on again. (Main power press [CH o / p] buttons on the remote control
button on the TV unit.)unit.
4. Switch the input mode to previous mode.
5. Turn the power off and on again. (Main power
button on the TV unit.)
5-4L3800EA |