AK36 CHASSIS MANUAL ADJUSTMENT PROCEDURE
In order to enter service menu, first enter the main menu and then press the digits 4, 7, 2 and 5 respectively.
To select adjust parameters, use Aor y buttons. To change the selected parameter, use < or > buttons.
Selected parameterwill be highlighted.
Entire service menu parameters of AK36 CHASSIS are listed below. For some of parameters the default values are
given on the same table.
REGISTER PARAMETERNOTE (NUMBERS ARE DEFAULT VALUES FOR CONCERNED ARAMETER)
OSD OSD Horizontal PositionADJUST HORIZONTAL POSITION FOR OSD
IF1 IP Coarse AdjustIF1 Adjust Course Neg. Adj. (WO / L')
IF2 IF Fine AdjustIF2 Adjust Fine Neg. Adj. (WO / L')
IF3 IF Coarse Adjust for L-PrimeIF3 Adjust Course Pos. Adj. (W / L')
IF4 IF Fine Adjust for L-PrimaIF4 Adjust Fine Pos. Adj. (W / L")
AGC Automatic Gain ControlAGC Adjust AGC
VLIN Vertical LinearityADJUST VERTICAL LINEARITY
VS1A Vertical Size for 50 Hz / 4:3ADJUST VERTICAL SIZE FOR 4:3 MODE (50 HZ)
VS1B Vertical Size for 50 Hz /16:9ADJUST VERTICAL SIZE FOR 16:9 MODE (50 HZ)
VP1 Vertical Position for 50 HzADJUST VERTICAL POSITION (50 HZ)
MP1 Horizontal Position for 50 HzADJUST HORIZONTAL POSITION (50 HZ)
VS2A Vertical Size for 60 Hz / 4:3ADJUST VERTICAL SIZE FOR 4:3 MODE (60 HZ)
VS2B Vertical Size for 60 Hz /16:9ADJUST VERTICAL SIZE FOR 16:9 MODE (60 HZ)
VP2 Vertical Position for 60 HzADJUST VERTICAL POSITION (60 HZ)
HP2 Horizontal Position for 60 HzADJUST HORIZONTAL POSITION (60 HZ)
RGBH RGB Horizontal Shift OffsetCVBS - RGB HORIZONTAL POSITION COMPENSATION
WR White Point Adjust for RED40
WG White Point Adjust for GREEN40
WB White Point Adjust for BLUE40
BR Bias for RED31
BG Bias for GREEN31
APR APR Threshold10
FMP1 FM Prescaler when AVL is OFF9 (STEREO ONLY)
NIP1 NICAM Prescaler when AVL is OFF20 (STEREO ONLY)
SCP1 SCART Prescaler when AVL is OFF13 (STEREO ONLY)
FMP2 FM Prescaler when AVL is ON13 (STEREO ONLY)
NIP2 NICAM Prescaler when AVL is ON16 (STEREO ONLY)
SCP2 SCART Prescaler when AVL is ON13 (STEREO ONLY)
F1H High Byte of crossover frequency for VHF1-VHF3MEANINGFUL FOR ONLY PLL TUNER (see tuner setting table)
F1L Low Byte of crossover frequency for VHF1-VHF3MEANINGFUL FOR ONLY PLL TUNER (see tuner setting table)
F2H High Byte of crossover frequency for VHF3-UHFMEANINGFUL FOR ONLY PLL TUNER (see tuner setting table)
F2L Low Byte of crossover frequency for VHF3-UHFMEANINGFUL FOR ONLY PLL TUNER (see tuner setting table)
BS1 Band Switch Byte for VHF1 Meaningful for onlyMEANINGFUL FOR ONLY PLL TUNER (see tuner setting table)
BS2 Band Switch Byte for VHF3 Meaningful for onlyMEANINGFUL FOR ONLY PLL TUNER (see tuner setting table)
BS3 Band Switch Byte for UHF Meaningful for onlyMEANINGFUL FOR ONLY PLL TUNER (see tuner setting table)
CB Control Byte Meaningful for only PLL TunerMEANINGFUL FOR ONLY PLL TUNER (see tuner setting table)
OP1 Option 1 (see the Option List)PERIPHERAL OPTIONS (see option table)
OP2 Option 2 (see the Option List)RECEPTION STANDART OPTIONS (see option table)
OP3 Option 3 (see the Option List)VIDEO OPTIONS (see option table)
OP4 Option 4 (see the Option List)TV FEATURE OPTIONS (see option table)
OPS Option 5 (see the Option List)CHANNEL TABLE OPTIONS (see option table)
TX1 Teletext Option 1 (see the Option List)TELETEXT OPTIONS (see option table)
14 |