6.2 OSD PositionNotes:
Call up the dialog line "OSD" with button "" via "DIALOG CENTER"- Should all video signal paths be in use on selection of AV because
�> "SERVICE" �> Service Code "8500".Copy is active for example, this situation is identified and the TV
With the buttons it is possible to shift the on screen display in theswitches over to the next technically possible AV position.
horizontal or vertical direction and to store this position "with mem.".- On selection of the country Italy in the menu, an AV-RGB signal with
blanking signal (Pin 16) has priority.
6.3 Hotel Mode- The blue screen background does not appear in all AV settings.
6.3.1 Activating the Hotel Mode
Call up the dialog line "Hotel" with button "" via "DIALOG CENTER"
AV socket configuration
�> "SERVICE" �> Service Code "8500".
With activated "Hotel Mode":
- it is no longer possible to call up the "DIALOG CENTER" menu withSocket InputOutputSwitching Signal
button "". AV1RGB-6/12V (switching voltage)
- the last volume setting is stored as the maximum level possible.+1V (fastblanking) evaluation
CCVSCCVS6/12V
6.3.2 Deactivating the Hotel Mode
Depress and hold button "" on the remote control handset whileSBAS (Y/C) CCVS6/12V
(converted)
switching the TV set on with the mains switch. Under the "SERVICE"
menu switch the Hotel Mode off. AV2RGB-6/12V + 1V evaluation
CCVSFBAS6/12V
6.4 Deactivating the Protection Circuit
Depress and hold button "" on the remote control handset whileSBAS (Y/C) CCVS6/12V
(converted)
switching the TV set on with the mains switch. As long as the Service
Menu is displayed the protection circuit of the TV set is not evaluated AV3CCVS-5V generated from sync
on video processor IC34015-(50). Camera
6.5 Selecting the Software (e.g. colour of the menu)
9. Changing the Picture Format
Call up the dialog line "OSD vertical" with button "" via "DIALOG
CENTER" �> "SERVICE" �> Service Code "8500".In AV mode, the picture format can be switched over with remote
With buttons "AUX" �> "OK" switch to the Toshiba software (colour ofcontrol button " " in dependence of the size of the picture tube.
the menu is red) and store "with mem.".The picture formate is changed between 4:3 and 16:9 in AV mode and
on the programme position with Peribit.
This status is indicated by the switching voltage applied to pin 8 of the
7. Setting the Analog ValuesAV 1 and AV 2 socket.
- 4:3 format 12V
- 16:9 format 6V
MaximumOptimumNecessary for 16:9 camcorder playback to compensate for the vertical
Brightness6332
extension because supply of the 16:9 switching voltage is not provided.
Colour contrast6340
Black/white contrast6348
Volume6330
Headphone volume6350
Tint6332
Bass2515
Treble2518
Sharpness 5 2
The analog values are stored automatically:
after about 8 seconds,
on switching to Standby mode,
on switching over from TV to AV mode,
on changing the individual AV settings.
Having stored the volume level the volume indicator bar is displayed
for about 10 seconds when switching the TV receiver on.
With "AUX" �> "OK" it is possible to re-set the optimum values for
picture and sound.
The optimum values are read out from EEPROM IC82005.
8. Audio / Video Connectors
Re-recording possibilities:
AV 1�>AV 2 (EURO-AV1 �> EURO-AV2 with 2 AV sockets)
AV 2�>AV 1 (EURO-AV2 �> EURO-AV1 with 2 AV sockets)
AV 3�>AV 1, AV2 (Camera �> EURO-AV1,2 with 2 AV
sockets)
AV 2�>AV 1 (Camera �> EURO-AV with 1 AV socket)
Re-recording is activated automatically by selecting button "0/AV" of
the source.
Copying function
Select the AV programme position using the "0 /AV" button then press
the "AUX" �> "0/AV" buttons to activate the copying function (indication
OCopy onO). During copying, you may switch to another programme.
Press the buttons in the same order again to deactivate the copying
function (indication OCopying offO).
1 - 17 |
ACEC
TOSHIBA
