29H-F200RU
WAVEFORM OR OTHERS
7-2
standardmoviemusicnews
ADJUSTMENT CONDITION / PROCEDURE
to select CONTRAST.CONTRAST effect is OK or not.to select COLOUR.COLOUR effect is OK or not.to select BRIGHTNESS.BRIGHTNESS effect is OK or not.to select BRIGHTNESS.BRIGHTNESS effect is OK or not.to select TINT.GREEN direction and DOWN for RED direction whether is OK or not.effect is OK or not. and whether LED(POWER SAVE) light up or not.to select WHITE TEMP.Option.pressed, all the settings will be present to normal setting. (Normal setting value for every mode, refer on the following figure).
(1) Receive "Monoscope Pattern" signal.(2) Press to Menu mode, then select Picture Mode and set (3) Press Volume Up/Down key to check whether the (1) Receive "Colour Bar" signal.(2) Press to Menu mode, then select Picture Mode and set (3) Press Volume Up/Down key to check whether the (1) Receive "Monoscope Pattern" signal.(2) Press to Menu mode, then select Picture Mode and set (3) Press Volume Up/Down key to check whether the (1) Receive "Monoscope Pattern" signal.(2) Press to Menu mode, then select Picture Mode and set (3) Press Volume Up/Down key to check whether the(1) Receive "NTSC Colour Bar" signal thru AV in.(2) Press to Menu mode, then select Picture Mode and set (3) Press Volume Up/Down key to check TINT, UP for (1) Receive "Monoscope Pattern" signal.(2) Set FEATURE to select SAVE.(3) Press Volume Up/Down key to check the POWER SAVE (1) Receive "Monoscope Pattern" signal.(2) Press to Menu mode, then select Picture Mode and set (3) Press Volume Up/Down key to check WHITE TEMP (1) Once in PICTURE Mode, and the NORMAL key is CONTRAST50604545 COLOUR0055 BRIGHT0550 TINT0000 SHARPNESS0000 PICTURE NRLOWLOWLOWLOW WHITE TEMP.01000
ADJUSTMENT POINTCONTRASTCOLOURBRIGHTNESSSHARPNESSTINTPOWER SAVEWHITE TEMPNORMAL
12345678
FUNCTION OPERATION CHECKING (1) (VIDEO & AUDIO)NO
Adjust these Horizontal and Vertical lines
WAVEFORM OR OTHERS50WAVEFORM OR OTHERSWAVEFORM OR OTHERS
(Adjusted point)
3dB)? 3dB)
?
7-1
ADJUSTMENT CONDITION / PROCEDUREADJUSTMENT CONDITION / PROCEDUREADJUSTMENT CONDITION / PROCEDURE
protector is not work.protector is work.in + B line, check all possible damaged components on +B line. (Use random selected set for inspection)Colour Bar, Sound 400Hz 100% Mod)Make sure the output is as specified (1.0 Vp-p Make sure the output is as specified (1.77 Vp-p
(1) Receive the "Monoscope Pattern" signal.(2) Press R/C to set Picture NORMAL condition.(3) Select full mode.(4) Adjust the focus control to get the best focusing.(1) Receive "Monoscope Pattern" signal.(2) Connect output of Bias Box to D757 cathode(3) Set voltage of Bias Box to 18V and make sure the (4) Set voltage of Bias Box to 27V, and make sure the (1) Once finish rectified Electrolytic Capacitor short testing (1) Receive the "PAL Colour Bar" signal (100% White (2) Terminate the Video output with a 75 ohm impedance.(3) Terminate the Audio output with a 10 Kohm impedance.Check of AVCheck of AVCheck of AVCheck of AVCheck of AVCheck of AV
ADJUSTMENT POINTFOCUSADJUSTMENT POINTHYV PROTECTOROTHER PROTECTORADJUSTMENT POINTAV OUTPUT CHECKAV-1 INPUT CHECKAV-2 INPUT CHECKComponent (50Hz 60Hz 480p 576p) INPUT CHECK REAR S-Terminal INPUT CHECKFRONT INPUT CHECKFRONT S-Terminal INPUT CHECK
FOCUS ADJUSTMENTNO1PROTECTOR OPERATION CHECKINGNO12A/V INPUT AND OUTPUT CHECKINGNO1234567
7 |
ACEC
SHARP
