Owners Manual
Amplier Operation
Power Control ConnectionsAmplier Operation
Your Outlaw amplier features a built-in remote turn-on system that will auto-After all connections have been made you are ready for listening. First, turn on
matically switch the unit on when another device in the system is switched on.the source components and processor in your system. It is always a good idea
to turn on your amplier LAST. This avoids the possibility of any turn-on pops
Remote Turn-On Using Products or transients from other equipment being amplied and sent to your speakers
Equipped With a 12 Volt Trigger Jack
where they may cause damage. Always start with a low volume level on your
Press the front panel power switch on the amplier so that it is in the ON posi-controller or preamp to avoid damage to your speakers.
tion. Then, using an accessory cable with a 3.5mm mono mini-plug on each
end, connect the trigger-output jack on the rear of the source device to the Manual On
trigger input jack on the back panel of the amplier. When these connections
Simply press the front panel Power/Standby button until the light is illuminated.
are made, the amplier will automatically turn on whenever the triggering There will be a short pause from the time the power is turned on until power
device is turned on.
is applied to the speakers. This is intentional, and protects your speakers from
Remote Turn on Using damage while the amplier stabilizes. You may also hear a relay click during
start up. This is also normal.
External AC to DC Power Converter
If your processor or receiver does not have a dedicated trigger jack, it is still To turn the unit off, press the Power/Standby button again. The indicator light
possible to activate the unit for automatic turn on when a Switched Outlet will go out.
is available on the rear of the source device. To control the amplier in this Automatic On
fashion you will need a small AC to DC power converter, capable of delivering
a 6 to 12 volt DC signal. The DC voltage should terminate in a standard 3.5mm Make certain that the connection to the processor, or other controlling device is
type mini plug. This type of converter may be obtained as a Power Adapter correct, as shown on page 6. Whenever the controlling device is turned on, the
from many electronics retailers.amplier will automatically turn on after a short pause. This pause is inten-
When installing, press the Main Power Switch on the front panel of the amplier tional, and it protects your speakers from damage while the amplier stabilizes.
You may also hear a relay click as during start up. This is also normal.
in so that it is in the ON position. Plug the AC adapter into a switched outlet that
will be activated when you wish to have the amplier turn on. This may be the To turn off your amplier, simply turn off the unit that feeds the amplier it?s
switched outlet at the rear of an AC receiver or other audio equipment. Connect audio signals. The amplier will automatically go into a stand by mode in a
the 3.5mm mini-plug from the adapter to the trigger-input jack on the back few moments.
panel of the amplier. The amplier will now turn on and off automatically,
Output Settings
based on the status of the controlling device.
All volume and level adjustments are made at your preamp, controller or sur-
Power Connectionround processor. To assure proper sound eld imaging, it is always a good idea
Once all audio and system connections have been made, connect the power to re-set the output levels of the channels on your processor when using the
cord to an AC power source. Please make certain that the amplier is turned amplier for the rst time. The circuitry in your new amplier may be different
off and that the device connected to the remote trigger input is off when con-from your previous one, and by checking the output levels you will make certain
necting the power cord and plugging it into an AC outlet.that the processor, amplier and speakers are properly matched.
CAUTION: Do not plug the your Outlaw power amplier directly into the Care and Maintenance
?Switched Accessory? outlet of another device! These outlets are intended
for use with low current draw products having a low current draw, such Cleaning
as tuners, CD players or cassette decks. These cannot handle the high When the unit becomes dirty, wipe it with a clean, soft, dry cloth. If necessary,
current draw of a power amplier. Using these outlets for a power ampli-rst wipe the surface with a soft cloth slightly dampened with mild soapy water,
er is a signicant safety hazard.
then with a fresh cloth dampened with clean water. Wipe dry immediately
with a dry cloth. NEVER use benzene, thinner, alcohol or any other volatile
NOTE: It is not recommended that you connect other power ampliers
or products with a high current draw, to the same AC power circuit as cleaning agent. Do not use abrasive cleaners, as they may damage the nish
your Outlaw power amplier, unless they are used with the remote power of the metal parts. Avoid spraying insecticide, waxes, polishing agents, or any
turn on and sequencing system. The simultaneous turn-on of multiple
aerosol product near the unit.
ampliers on the same circuit may cause circuit breakers to trip, due to
the high current draw.When You Are Away
If you will not be using your home theater system for an extended period of
time, it is always a good idea to turn the unit off using the Power Switch on the
front panel of the amplier. This will prevent the automatic turn on circuits
from accidentally turning the system on during your absence.
Seven-Channel P7ower Amplier |
ACEC
OTHERS
