3gb15037.fm Page 2 Monday, November 4, 2002 2:24 PM
Note: The programme stops to ?Rinse Hold? at the The indicator lamps show the sequence reached in
CONSUMPTION DATA
time the ?Rinse Hold? light in the programme flow the programme. After starting the programme, the
indication is on.sequence indication runs from left to right through
Temperature SelectorLoadWaterEnergyApprox. Programme
ProgrammeDurationTerminate the ?Rinse Hold? option:Wash, Rinse, Spin.
? Press the ?Rinse Hold? button again; the When the sequence of the programme is finished
(°C)(kg)(l)(kWh)(hours : minutes)*
Cotton955.044**1.601:55programme will terminate automatically with the the corresponding lamp goes out.
final spin cycle for the present wash programme.
Cotton605.0390.952:00? If you do not wish to spin the clothes, turn the DOOR LOCK
Cotton405.0390.552:00programme selector knob to the ?Drain?
programme and press the ?Start/Pause? button During the first 15 minutes of the cotton and
Synthetics602.5550.701:30synthetics programmes the door can be opened for
Synthetics402.5500.501:15again when flashing.adding further laundry.
?Variable Spin? button
Daily 60403.0470.481:00The door can be opened when the ?Door Open?
? Every programme has an automatic predefined
Rapid Plus303.0350.400:30maximum spin speed.indication is shining.
Delicates301.5500.500:45? Press the button to set another spin speed.
PROGRAMME END
Wool401.0500.500:40? If the spin speed ?0? is selected, the final
spinning is cancelled but intermediate spin ? The remaining time is on ?0:00? and all the
Silk301.0350.400:35
peaks remain during rinse. The water is drained lights of the programme sequence indication
Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized out only.are off.
conditions in compliance with Standard IEC 60 456. Consumption data in the home may vary with respect to the values in
the table in relation to the water supply pressure and temperature, the load and the type of wash.START DELAY1. Turn the programme selector to the ??
* The remaining time indicator can similarly deviate from the values in the table, because it takes into account the position.
household conditions applicable at that time.The ?Start Delay? allows to run the machine at the 2. Turn the water supply tap off.
**To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the consumer?s convenience, for example at night 3. Open the door and unload the machine.
water out.when electricity is cheaper.4. Close the tap and leave the door ajar to allow
? Select programme, temperature and options.the drum to dry out.
ADD DETERGENTS, CLOSE THE DOOR AND SELECT THE ?Easy Ironing? button
PROGRAMME? Can be used together with Cotton, Synthetics and ? Press the ?Start Delay? button to select the
delay time by 1 to 19 hours;CHANGE THE PROGRAMME, TEMPERATURE,
Add the detergents as described in the programme Daily 60 programmes to make ironing easier.?Press the ?Start/ Pause? button. The ?Start OPTIONS AFTER PROGRAMME START
? Increases the water quantity and the clothes are
table or in the chapter ?Detergents and Additives? in spun very soft.Delay? light flashes until the programme starts.1. Press the ?Start/Pause? button to pause the
the booklet.? The time delay indication disappears when the
?Prewash? buttonprogramme. The light flashes.
programme starts and it is replaced by the
1. Turn the programme selector knob to the ? Only for heavily soiled loads (for example sand, remaining time.2. Select the new programme (with temperature),
desired programme.granular dirt) sensible. The cycle time increases ? The number of hours preselected can later be any options and another spin speed if you
2. The remaining time display shows the duration of approximately 15 min.want.
reduced pressing again the ?Start Delay?
the chosen programme (in hours and minutes) ?Intensive Rinse? buttonbutton.3. Press the ?Start/Pause? button again. The
and the pilot lamp of the ?Start/Pause? button ? A further rinse cycle is added.new programme continues at the same position
is flashing.? This option is particularly suitable for areas with To cancel the ?Start Delay?.where the previous programme was
? Turn the programme selector to the ? ?
3. The programme sequence and the predefined very soft water, washing baby linen and helps interrupted. Do not add detergent for this
spin speed indication corresponding to the people with allergies.position.programme.
? Reselect the desired programme and options
selected programme lights up.?Rinse Hold? buttonand press the ?Start/Pause? button.
The recommended temperature (see the indicator) CANCEL A PROGRAMME BEFORE THE END
can be altered by pressing ?+? or ?-? button.? The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing PROGRAMME START
and prevent colours from changing.1. Press the ?Start/Pause? button to pause the
SELECT ANY DESIRED OPTIONOpen the tap and press the ?Start/Pause? button. programme. The light flashes.
? This option is particularly recommended for the 2. Set the programme selector to ?Drain?. The
Selecting any option the indication lights up.programme ?Synthetics?, ?Daily 60? and The pilot lamp of the ?Start/Pause? button lights up.
spin indicators show ?0? and the remaining
When the combination of programme, additional ?Delicates?.time shows ?0:02?.
options and temperature is not possible, the ? This function is particularly useful if you want to
indication lights switch off automatically. postpone spinning to a later time, or if you want 3. Press the ?Start/Pause? button to start the
drain programme.
Unsuitable combinations of options are to drain only.
deselected automatically.
Whirlpool is a registered trademark of Whirlpool USA
5019 301 15037
Black process 45.0° 100.0 LPI |
ACEC
WHIRLPOOL
