FanTimer
Press FAN to choose High, Med, Low or Auto.To set Timer for a 30-minute to 24-hour delay before air
NOTE: Auto fan speed cannot be selected in Fan mode.conditioner is turned off (air conditioner must be On):
1. Press TIMER. Timer indicator light on the air conditioner
control panel will flash.
Sleep Control
2. Press up or down arrow button to change the delay time from
NOTES: 30 minutes to 24 hours.
 If the current room temperature is 80oF (26oC) or higher, the 3. After 5 seconds. Timer indicator light on the air conditioner
set temperature will not change when Sleep control is control panel will remain on.
activated.
To set Timer to turn on air conditioner, keeping previous
 If the current room temperature is below 80oF (26oC), the set
settings:
temperature will automatically increase 2oF (1oC) during the
1. Turn off the air conditioner.
first 2 hours after Sleep control is activated.
2. Press TIMER. Timer indicator light on the air conditioner
The set temperature will not increase during the last 6 hours
control panel will flash.
of Sleep control.
3. Press up or down arrow button to change the delay time from
1. Press MODE to select Cool or Dry.30 minutes to 24 hours.
2. Press FAN to select High, Med or Low.4. After 5 seconds, Timer indicator light on the air conditioner
3. Press the up or down arrow button to set the temperature. control panel will remain on.
4. Press SLEEP. After 10 seconds, the lights on the control
To set Timer to turn on air conditioner, changing the
panel display will dim. The mode indicator lights will remain
previous settings:
on.
1. Turn on air conditioner.
NOTE: The mode, temperature and fan speed may be
th?
adjusted during Sleep control. After 10 seconds, the lights on 2. Adjust the mode to 6 Sense System control, Cool, Dry, Fan
?
the control panel display will dim again.or RapidCoolcontrol.
3. For Cool mode:
 Adjust fan speed to High, Med, Low or Auto.
 Adjust temperature between 64oF and 90oF (18oC and
32oC).
5. To turn off Sleep control, press SLEEP again. or wait 8 hours 4. For Fan mode, adjust fan speed to High, Med or Low.
for the air conditioner to turn off automatically.NOTE: In Fan mode, temperature cannot be set.
NOTE: The air conditioner will return to previous settings after th?
5. For 6 Sense System control, adjust fan speed to High,
Sleep control is turned off.
Med, Low or Auto.
th?
6. For Dry mode and 6 Sense System control, adjust
Temperature
temperature up or down by 4oF (2oC).
7. Turn off air conditioner.
 Press the up arrow button to raise the temperature. Each time
you press or hold the up arrow button, the temperature will go 8. Press TIMER. Timer indicator light on the air conditioner
up 2oF (1oC) until it reaches 90°F (32°C).control panel will flash.
9. Press up or down arrow button to change the delay time from
30 minutes to 24 hours.
10. After 5 seconds, Timer indicator light on the air conditioner
control panel will remain on.
 Press the down arrow button to lower the temperature. Each
time you press or hold the down arrow button, the To clear Timer delay program:
temperature will go down 2oF (1oC) until it reaches 64°F NOTE: Air conditioner can be either on or off.
(18°C).1. Press TIMER once after it has been programmed. Display will
show remaining time.
2. While the display is showing the remaining time, press TIMER
again. Timer indicator light will turn off.
To see or change the remaining time (in hours):
1. Press TIMER once after it has been programmed. Display will
show remaining time.
2. While the display is showing the remaining time, press the
plus or minus TEMP button to increase or decrease the time.
3. After 5 seconds, the display will show the current room
temperature.
11 |
ACEC
WHIRLPOOL
