Rear panel facilities and connections
SPEAKERSY When you are using only one
speaker or when you wish to
Connect the jacks on the speakers to the SPEAKERS terminalsNO!
listen to monaural (mono)
using the speaker cables. These terminals are compatible with
sound, a single speaker should
banana plug connections.
never be connected in parallel
5
1 Strip away 15 mm (/8 in.) of wire insulation.to both the right and left-
2 Twist wire ends very tight.channel terminals simultane-
+� � ++� � +
ously.
3 Unscrew.RLRL
4 Insert wire.
Y To prevent damage to cir-
5 Screw.
cuitry, never short-circuit the
15mm
1(5/8 in.)2positive (+) and negative (�)
NO!
speaker wire.
345
AC INLET
Plug the supplied power cord into this AC INLET and then into the
power outlet on the wall.
Y Do not use a power cord other than the one supplied with the
ADM-2.1. The power cord supplied is designed for use with
Y Do not connect any devices other than speakers to thesethe ADM-2.1 and should not be used with any other device.
terminals.
Y Never disconnect the power cord from the ADM-2.1 while the
Y Be sure not to mistake the positive and negative outputs or theother end is plugged into the wall outlet. Doing so may cause
left and right speakers. Doing so will result in an unnaturalan electric shock. Always connect by plugging into the wall
sound space.outlet last and disconnect by unplugging from the wall outlet
Y Only connect speakers with an impedance of 6 ohms or higher.first.
If a speaker with an impedance of less than 6 ohms is
connected, it may damage the ADM-2.1.
Connection diagram
Since the many users will purchase the ADM-2.1 together with theWhen connecting the ADM-2.1 to 2 channel control amplifier or
DTR-7.1, here is an explanation of how to connect the ADM-2.1 topreamplifier, connect the AUDIO IN jacks of the ADM-2.1 to the
the DTR-7.1.PRE OUT FRONT jacks of the control amplifier or preamplifier,
and connect the front speakers to the SPEAKERS terminals of the
ADM-2.1.
12V TRIGGER OUT jack
DTR-7.1
ANTENNAAM75FMCOMPONENTVIDEORS 232
REMOTE RLFRONT
DIGITALOUTPUTCONTROL(OPTICAL)YSPEAKERS
TRIGGER12 VPRE
BAROUTLZONE 2 MAININPUT 1
1FRONTIR INCENTERAC OUTLETS
DIGITALPBINPUTRLVIDEOS VIDEOSURRSPEAKERAC 120V 60HzTOTAL 120W 1A MAX.SWITCHED
OPTICAL2SURROUTPR()SPEAKERBACK
PRE OUTGNDSURRBACK(SB)VIDEO1RL
1I NY
DIGITAL SUB
SURR BACK(COAXAL)INPUTWOOFERCENTERINPUT 2SURRSPEAKERS
2OUTPB
jacksRLV IDEO2FRONTRLMAINCAUTION: OUTI NPRZONE 2SPEAKER IMPEDANCE
6 OHMS MIN. PER EACH
SPEAKERSTAPEV IDEOSPEAKER TERMINAL3
SURRINI NYZONE 2AC INLET
(SB)OUTPUT
SURRCDDVDBACKI NPBAV RECEIVERMODEL NO. DTR-7.1
SUBWOOFERPHPR
MULINPUTTI CHANNEL CENTERZONE 2RLROUTMONLVIDEOOUT ITORS VIDEO
ADM-2.1
AC INLET
GNDSPEAKERS2 CHANNEL AMPLIFIER
MODEL NO. ADM-2.1
INPUTTRIGGER 12 V LLAUDIOLEVELTRIGGERPower cord
OUTIN
(supplied)
LL
AUDIO OFF TRIGGERRIN12 VR
RR
MINMAX
Set to 12V TRIGGER.
SurroundSurround
back rightback left
speakerspeakerTo an AC
wall outlet5
#US_ADM-2.1_04-07.p6558/25/00, 6:22 PM |
ACEC
ONKYO
