24093_ADP 303 Eng. 27/02/1998 10:34 Side 11
Installation & Setup
10
INSTALLATION &
LV PlayerLine Audio OutDVD
AC-3 12
CALIBRATION RF OutputLAC-3 Data
WITH AV RECEIVERS/R
AMPLIFIERS WITH
132
PRE-OUT/MAIN-IN
JACKS9
LARGESMALLLARGESMALLLARGESMALLONOFFAC OUTLET
ADP 303FRONT SPK.SURR. SPK.NONCENTER SPKNONSUB. W SPK
MODEL NO.: ADP303HARMAN KARDONIN
NORTHRIDGECALIFORNIA, USA
MADE IN JAPANOUT
AC-3RF IN DIGITAL INAC-3COAXDIGITAL INAC-3L RSURROUNDL RCENTER WOOFERSUBOPT
UNSWITCHED
68
5
7
AV Receiver LINE IN
PRE OUT
L RCENTERL R
4FRONTSURROUNDL RSUBPoweredLDWOOFER
MAIN INOUTSubwoofer
AUDIO IN
Although AV receivers that have both pre-7. Connect the Line Out ° jacks of thestopping for five seconds at each speaker.
out/main-in jacks for all five surroundADP303 to the Main-In jacks on the rearIf the sound is heard out of order, (i.e.,
channels as well as a subwoofer outputof your receiver. moving from right to left, or appearing
were not designed for Dolby Digitalout of order), turn the unit off and check
8. Connect the ADP303 Subwoofer output
applications, you may use them with thethe connection from the ADP303 output
jack to a powered subwoofer or a sub-
ADP303 by using the following steps:jacks to the inputs of your audio power
woofer amplifier.
amplifiers.
1. Connect the AC-3 RF output of a com-
9. Set the Speaker mode switches
patible LV player to the ADP303 AC-3 RF15. Listen to the sound as it moves
¤?Y?to their proper positions
In Jack �.between the speakers. Ideally, the output
based on the type of speakers in use.
from each speaker should be equal. If the
2. Connect the optical or coax AC-3 out-
10. Using the small Allen wrench tooloutput is NOT equal change the level by
put of a DSS, DVD player or HDTV receiv-
supplied with the ADP303, carefullycarefully turning the Output Level Trim
er to the respective input jack aL on
remove the cover panel for the LevelControl ú for the speaker that needs
the ADP303.
Trim Controls ú. Set the cover aside soadjustment.
3. Connect the Line Audio out from thethat you may replace it later.
NOTE: If you have trouble getting suffi-
Laser Disc player to the LD audio input
11. Turn on the power to both thecient output level from the ADP303 trim
on the receiver.
ADP303 and the AV receiver.controls increase the master volume level
4. After making certain that the power tousing the ADP303 volume control ?. If
12. Select one of the three digital inputs
your receiver is turned off, remove anythe volume level is too loud reduce the
on the ADP303. ?.
jumpers that connect the Pre-out tolevel of the ADP303 master volume ?.
Main-In jacks on the rear of your AV13. Set the Main Volume Control ? on
16. When you have completed the adjust-
receiver.the ADP303 to the fully clockwise (lowest
ments, press the OTest� � button once
volume) position.
5. Connect the Pre-Out jacks on theto stop the Test Tone.
receiver to the respective Line Input Jacks14. Press the Test button � and hold it
17. Carefully replace the cover for the
c(i.e., left to left, center to center, etc.)for a few seconds. This will start the test
Level Trim Controls.
of the ADP303.tone sequence. Raise the volume on the
ADP303 ? until you hear the test signal18. When listening to a Dolby Digital
6. Connect the sub out jack on the
at a level slightly above normal volume.source use the volume control on the
receiver to the Subwoofer input jack on
ADP303 ?. For all other lsitening set the
the ADP303.Note that a test signal noise will be heard
ADP303 to BYPASS Ť,or turn it off. Use
from the speakers. Verify that the test sig-
the A/V ReceiverOs volume control for all
nal circulates in a clockwise direction,
other (non-Dolby Digital) modes. |
ACEC
HARMAN KARDON
