Ensure that the charcoal filter is fitted to the motor supporLight button rtaised: lights off
(Fig. 12/13)
The push buttons numbered OFF/1 - OFF/2 - OFF/3 - OFF/
4.Fitting the telescopic chimney stack4 - TURBO 1-2-3 control the fan speeds.
The chimney stacBk consists of two U-shaped sections: aPush buttons OFF/ 1 : activates or disactivates speed
lower section C and a upper section D (Fig.1).1, low speed; it should be selected when simmering
or when using only one pan;
Caution: Before fixing the hood to the wall fit the lower
Push buttons OFF/ 2 : activates or disactivates speed
chimney.
2, intermediate speed; it should be selected for normal
Put the chimney stack into the recess in the top of thecooking up to four pans;
canopy hood ensuring that the holes at the bottom of the lower
Push buttons OFF/ 3 : activates or disactivates speed
section D coincide with the holes in the recess of the canop3, top speed;y. it should be selected when frying or cooking
To fix the lower section C to the canopy use NoM scre. 2 wsfood with strong odours.
acting from the inside of the canopy (Fig 10). Lift the upper
Push buttons TURBO 1-2-3 : ativc ates or disactivates
section D up to the ceiling and fix it to the wZ withall bracthe ket TURBO speed, which works once one of the pther
two screws M on both sides of the section D (Fig. 11).
speed buttons has been pressed.
OPERATION
W ORKTOP ILLUMINATION
- Version sliderTwo lamps of 40 Watt or two halogene lamps of 20 Watt or
The cooker hood functions are controlled by two sliderFour halogene lamps of 10 Watt, ensure the worktop
switches located in the front of the hood or in the infillumination.erior part. If a lamp fails to function at any time, an
identical replacement must be fitted to ensure the safe
The two slide switches control the fan speeds and the
working of the cooker hood.
worktop illumination . A red pilot lamp, located between the
two sliders, illuminates when the motor is working.To replace the lamp proceed as follows:
The switch marked with the lamp symbol and numbered 0-- Disconnect the hood from the mains supply;
1 controls the worktop illumination.- With the use of a small screwdriver unhook the spring A and
Position 0 : the light is off.the glass cover will be released;
Position 1 : the light is operating.
- Remove the burned lamp and fit a new one;
The switch marked with the fan symbol and numbered
0-1-2-3- controls the fan speed:Note: pay special attention to the warnings contained in the
instructions leaflet accompaniyng the new halogene lamp.
Position 0 : the fan is off;
Position 1 : low speed; it should be selected when- Refit the glass cover and the spring A.
simmering or when using only one pan;
If a lamp fails to function at any time, first check that it is
Position 2 : intermediate speed; it should be selected
fully screwed into the holder.
for normal cooking up to four pans;
Position 3 : top speed; it should be selected when frWhen changing the lamp an identical replacement myingust
be fitted to ensure the safe working of the cooker hood, do not
or cooking food with strong odours,
remove the light cover to replace the lamps but operate inside
To obtain the best performance it is advisable to switch on
the hood removing the metal filters.
the hood a few minutes before you start cooking and leave it
running for approx 15 minutes after finishing.
- 3-speed push button panel
MAINTENANCE AND CLEANING
The cooker hood functions are controlled by the pushW ARNING Before carrying out any kind of maintenance
bottons located in the front part of the hood. A red pilot lampor cleaning disconnect the hood from the mains supply.
illuminates when the motor is working. The push button with
Regular maintenance and cleaning will ensure good
the lamp symbol controls the worktop illumination (0-1).
performance and reliability, whilst extending the working life
The push buttons numbered 1 - 2 - 3 control the fof the hood.an speeds.
Cleaning
Position 1 : low speed; it should be selected whenFor your own safety and in the interest of hygiene your
simmering or when using only one pan;
hood needs to be kept clean.
Position 2 : intermediate speed; it should be selected
for normal cooking up to four pans;Wipe over the hood with a soft cloth wrung out in hot
water and containing a mild household cleaner and dry with a
Position 3 : top speed; it should be selected when frying
or cooking food with strong odours.soft cloth. Never use excessive amounts of water when
cleaning, particularly around the control panel area.
- 4-speed push button panel
Never use abrasive cleaners as they might scratch or
The cooker hood functions are controlled by the pushdamage the surfaces.
bottons located in the front part of the hood. A red pilot lamp
illuminates when the motor is working. The switch with theMaintenance
Special attention should be given to the grease filter and
symbol of an on/off light contols the lighting system.
to the charcoal filter/s if the hood is used in the recirculation
Light button pressed: lights on
mode.
3 |