Setup menus (continued)
SYSTEM
No./ItemDescription of settingNo./ItemDescription of setting
05For setting whether to perform the various 15For adjusting the system phase of the analog
ENCODERadjustments for the video output signals using this VO SYS Hcomposite output signals (in 37 ns increments).
SELVTR or using an external encoder remote controller.(SD)- :Phase advances.
0001LOCAL :+ :Phase delays.
The various adjustments for the video output 0000-858
signals are performed using this VTR. : :
0002 BOTH :08580
The various adjustments for the video output : :
signals are performed using both this VTR and an 1716858
external encoder remote controller.<Note>
<Notes>The setting range is -864 to 0 to 864 when 50i/25P,
z For video adjustments, refer to ?Video output signal 25 (HD) or 25 (SD) is selected as the menu item
adjustments? (page 35).No.25 SYSTEM FREQ setting.
z If the signals are adjusted with the external 16For adjusting the system phase of the SD SDI output
encoder remote controller, the adjusted values are
reflected in the setup menu. However, the adjusted SD SYS Hsignals (in 37 ns increments).
(SD)- :Phase advances.
numerical values will not be stored unless about 1 + :Phase delays.
minute has elapsed after completion of the
adjustment operation. If the unit is turned off after 0000-858
: :
executing the adjustments with the external 08580
encoder remote controller, it is necessary to wait
: :
about 1 minute before turning off the power.1716858
z Settings in this menu are not effective for the <Note>
IEEE1394 digital output.
The setting range is -864 to 0 to 864 when 50i/25P,
06For selecting what is to be controlled when the video 25 (HD) or 25 (SD) is selected as the menu item
V LEVELoutput level is to be adjusted by an external encoder No.25 SYSTEM FREQ setting.
CTRLremote controller.18For adjusting the SCH (sub-carrier to horizontal)
0000HD :
SCHphase of the analog composite output signals (4
The HD video output level can be adjusted.
0001SD :COARpositions in 90-degree increments).
The SC phase changes, and the H phase remains
The SD video output level can be adjusted.(SD)unchanged.
0002BOTH :
Both the HD and SD video output levels can be 00000
000190
adjusted.0002180
<Note>
0003270
When ?CMPST? is selected in menu No. 650 STYLE,
the unit will be in the same state as when ?BOTH? is 19For adjusting the SCH (sub-carrier to horizontal)
selected, regardless of the settings in this item.SCH FINEphase of the analog composite output signals
12For adjusting the system phase of the HD SDI output (SD)(variable range of over ?45 degrees).
The SC phase changes, and the H phase remains
SYS Hsignals. (in 13.5 ns increments).unchanged.
(HD)- :Phase advances.A range of ?180 degrees is covered by using this
+ :Phase delays.setting in combination with item No.18 SCH COAR
0000-1100(SD).
: :
0000-32
11000 : :
: :
2200110000320
: :
<Notes>006432
z When menu item No. 25 SYSTEM FREQ is set to
20For adjusting the phase of the AUDIO output signals
50i/25P, 25 (HD), 25(SD), 50 (HD) or 50 (SD), the
setting range is from -1320 - 0 - 1320.AVin relation to the video output signals (in 20.8 ?s
increments).
z When menu item No. 25 SYSTEM FREQ is set to PHASE- :Audio phase against image advance.
23/24, the setting range is from -1375 - 0 - 1375.
+ :Audio phase against image delay.
14For adjusting the system phase of the analog 0000-100
SYS SCcomposite output and SD SDI output signals (total : :
(SD)variable range of over ?180 degrees).01000
- :Phase advances. : :
+ :Phase delays.0200100
0000-108
: :
01080?_____? indicates the factory setting.
: :
0216108
36 |
ACEC
PANASONIC
