Error messages (continued)
Warning messages (continued)
Priority Monitor displayDescriptionCorrective actionVTR operation
E-00
This appears when the servo is not locked for three or Operation
(SERVO NOT Check the tape.
more seconds during playback or recording.continues.
LOCKED)
(In 23.98/24 Hz mode)
Display when the time code is recorded in DF mode. On
the drop point of the time code, the video output is
E-93Use the original tape recorded
garbled and audio output is muted. Operation
(INVALID TC with the variable frame rate
Operation of VTR continues. continues.
MODE)camera.
When using this unit to playback a tape recorded from a
variable frame rate camera, it is necessary to record the
time code in NDF mode.
(In 23.98/24 Hz, 25 Hz, 50 Hz mode)
Appear when the relationship between the active frame
information and time code is not regular during playback.
The video output may not be regular (not smooth).
E-94Use the original tape recorded
Operation of VTR continues.Operation
(TC SEQUENCE with the variable frame rate
The active frame information (top frame of the switched continues.
UNMATCH)frame image) is recorded on the tape from a variable camera.
frame rate camera. To play it back with this unit, it is
necessary to detect the 0 frame of the time code at the
activation frame position.
This appears when an envelope level approximately one-
E-01Operation
third of the normal level has been detected for more than Clean the video heads.
(LOW RF)continues.
one second during playback or recording.
E-02This appears when the error rate has increased to the
Operation
(HIGH ERROR extent that correction or interpolation was applied to Clean the video heads.
continues.
RATE)either the video or audio playback signals.
Low
Error messages
VTR
Monitor displayDescriptionCorrective action
operation
The unit switches to eject mode and if the cassette fails to move up
within 6 seconds, this error number flashes on the display.
E-29
<Note>Set the POWER switch to OFF
FRONT LOAD STOP
If the cassette does not move down inside the machine even when 6 and then to ON again.
MOTOR
seconds have elapsed since the cassette was inserted, the VTR is
transferred to the eject mode.
If the unloading operation is not completed within 6 seconds, this
error number flashes on the display.
E-31Set the POWER switch to OFF
<Note>STOP
LOADING MOTORand then to ON again.
When the loading operation is not completed within 6 seconds, the
VTR is transferred to the eject (unloading) mode.
E-35
If there is no response from the servo microcomputer for 1 second Set the POWER switch to OFF
SERVO CONTROL STOP
or more, this error number flashes on the display.and then to ON again.
ERROR
E-37If 10 seconds or more elapses and the servo microcomputer has not
Set the POWER switch to OFF
SERVO COMM followed orders issued by the system control microcomputer, this STOP
and then to ON again.
ERRORerror number flashes on the display.
This appears when the automatic reel and capstan rotation
E-38Set the POWER switch to OFF
adjustment, which is performed in the EJECT mode, has not been STOP
SERVO FG ERRORand then to ON again.
carried out properly when the unit?s power was switched on.
E-51If the take-up reel rotates without engaging for a specific period of
Set the POWER switch to OFF
FRONT LOAD time during the start or end processing operation while loading is STOP
and then to ON again.
ERRORunderway (half position), this error number flashes on the display.
If the take-up reel fails to take up the tape while the tape is traveling
E-52
in the state where the total amount of the tape has not yet been Set the POWER switch to OFF
W-UP REEL NOT STOP
detected after the cassette was inserted, this error number flashes and then to ON again.
ROTA
on the display.
If there is an abnormally large discrepancy between the amount of
tape taken up by the take-up reel and the amount of tape supplied
E-53Set the POWER switch to OFF
by the supply reel while the tape is traveling after the total amount of STOP
WINDUP ERRORand then to ON again.
the tape begins to be detected, this error number flashes on the
display.
62 |
ACEC
PANASONIC
