ifu_az1053_eur_eng 14/9/07 17:47 Page 3
Power supply/Basic operationAlarmAlarm/Digital tuner
To change time formatexcept REPEAT ALARM /
Power supplyBRIGHTNESSTurning on/off radio
1 In the Clock menu, press 3 4 to select the.
CONTROLY To turn off radio, press OK.To turn on radio,
1 Connect the supplied power adapter to the
value of O12/24 Hour Format�.�is displayed.press OK again.
set's DC 9V socket and to the power socket.
2 Press 12 to toggle between 12H and 24H.
Repeat alarm
Helpful hints:To improve reception:
Note:This will repeat your alarm call at 9-minute
To avoid damage to the set, use only theFM: Extend and adjust the pigtail for optimum
When the set is disconnected from the powerintervals.reception.
adapter supplied!
outlet for about 5 minutes, you need to reset the1 During the alarm call, press
The type plate is located on the bottomtime and date.REPEAT ALARM / BRIGHTNESS CON-Programming radio stations
of the set..You can store up to a total of 20 FM radio
TROL
Setting and activating alarm �flashes.stations in the memory, manually or automat-
Setting OSD (On Screenically (Auto store).
You can set two different alarm times.Switching off the alarm completely
Display) language
1 Press CLOCK.1 Press repeatedly ALARM 1 or ALARM 2Manual programming
1 Press MENU.2 Press and hold ALARM 1 or ALARM 2.until is changed to .1 Tune to your desired station (See OTuning to
�The menu appears.�The hour digits flash.�When alarm is deactivated,is dispalyed.radio station�).
2 Press 12 to highlight OGeneral�.3 Press or hold down 3 4 to set hour.2 Press and hold TUNER for about 2 sec-
Helpful hints:
3 Press 4 to highlight OLanguage�.4 Press ALARM 1 or ALARM 2 to confirm.onds, then release.
During alarm call, if no button is pressed, alarm
4 Press 12 to select desired language.�The minute digits flash.�Preset number will flash.
call will last 30 minutes.
5 After finishing the setting, press CLOCK,5 Press or hold down 3 4 to set minute.3 Press 34 once or more to allocate a
number from 1 to 20.
TUNER, PHOTO or MUSIC to exit the6 Press ALARM 1 or ALARM 2 to confirm.
�Preset number will flash.
setup menu.7 Press again ALARM 1 or ALARM 2 toTuner
4 Press TUNER again to confirm.
activate alarm setting.
5 Repeat steps 1-4 to store other stations.
Setting time and date �When alarm is activated,is displayed.
Note:
�At the set alarm time,the alarm will sound
� You can erase a preset station by storing
and its volume will increase gradually.
another frequency in its place.
Selecting alarm mode
Auto store
1 Press MENU.Autostore automatically starts programming
�The menu appears.radio stations from preset 1.Any previous
2 Use 12 to highlight OClock�.presets e.g. manually programmed will be
3 Press 34 to select OAlarm Music�.erased.
4 Press 12 to select specific music you like.1 In TUNER mode, press MENU to display
�Alarm will go off with the music you select.tuner menu.
Tuning to radio station
2 Press 4 to select OTuner Auto Program�.
1 Press MENU.Switching off the alarm 1 Press TUNER to switch on radio (FM only).3 Press OK.
�The menu appears.There are three ways of switching off the2 Press and hold 12 for about 2 seconds,�Available stations are programmed (FM).
then release.
2 Use 12 to highlight OClock�.alarm. Unless you choose to cancel the alarmAfter all stations are stored, the first auto-
�The radio automatically tunes to a station
3 Use 3 4 1 2 to select a field of OTime Set�completely, the DAILY ALARM RESET optionstore preset station will then automatically
of sufficient reception.
and ODate (Year-Month-Day)�.will be automatically kept activated from theplay.
3 Repeat step 2 if necessary until you find the
4 Press OK to confirm.time your alarm first goes off.
desired station.
5 Press or hold down 3 4 to set the values.call at the same time for the following day:To listen to a preset or autostore
YTo tune to a weak station, press 12 briefly
6 Press OK to confirm.station
Daily alarm reset and repeatedly until you have found optimalPress 34 once or more until the desired
7 Repeat Steps 3-6 to set other values ofreception.
If you want the alarm to be stopped preset station is displayed.
OTime Set and ODate (Year-Month-Day)�.
immediately but also wish to repeat the
8 After finishing the setting, press CLOCK,
alarm
TUNER, PHOTO or MUSIC to exit the
setup menu.1 During the alarm call, press any button |
ACEC
PHILIPS
