Parts and their functions
CRISP:CrispCRISP:Skin tone detail crisp
This is used to set the maximum amplitudeThis is used to remove the very faint noise
of the very faint noise components whichcomponents from the detail components of
are to be removed from the detailthe skin tone areas.
components.SKIN LVL: Skin detail level
PEAK1:Peak frequencyThis is used to set the chroma saturation of
This is used to select one of the twothe parts where the skin tone detail is
contour correction frequency bands (boostapplied.
frequency or peak frequency).
PEAK2:Peak frequency8Camera power switch indicator
This is used to select one of the twoThis is the indicator of the cameraOs power ON/OFF
contour correction frequency bands (boostswitch.
frequency or peak frequency).Lights up green: The unit is communicating with the
LEVEL DEP: Level dependentcamera.
This function removes the detail in the darkLights up red:The unit is not communicating with the
parts by means of a coefficient dependentcamera.
upon the video signal level so that the darkFlashes red:POWER OFF status established by
parts will not appear unnatural.software.
DARK:Dark detail
This function boosts the detail in the dark
9HEAD POWER
parts.
CORNER:Corner detail
:All switch [ALL]
This function boosts the detail around the
When the lamp of this switch is lighted, the switch can be
edges of the screen.
used to control the switch (CAM/BAR/TEST) inside the
SOURCE:Detail source
MODE frame, the switches inside the AUTO frame and
This is used to select the source signals for
GAIN frame as well as the IRIS CLOSE switch and the
creating the detail components.
ND and CC filter positions for all the cameras whose
CLIP:Detail edge clip
power is on and which are connected to the MSU.
This is used to limit the length of the detail
The camera selector switches flash, and the other
edge components.
switches light. When a switch with a lighted lamp is
DTL KNEE: Detail edge knee
pressed and its lamp is turned off, the corresponding
This function applies the knee to the detail
camera is no longer subject to the ALL function.
edge parts.
When the lamp of the ALL switch is off, the MSUOs
CRM DTL:Chroma detail
camera operations performed for the cameras selected
This is used to enhance the contours of the
by the camera selector switches are valid unless
areas with a high chroma saturation in the
otherwise specified.
subjects.
When the switch is pressed again while its lamp is
CRM CRSP: Chroma detail crisp
lighted, the ALL function is released.
This is used to ensure that the chroma
detail is not added to the very faint noise
components below the level set.;CARD
This lights up green when an SD card has been inserted.
SDTV skin tone detail switch [SD.SKIN]
This is used to apply coring to the detail enhancement of<SD card slot
the skin tone areas in the SDTV video output signals toThis is where the SD cards (hereafter Ocards�) are
soften the skin tone detail enhancement.inserted. By taking the prescribed steps, the data of the
It cannot be selected when the lamp of the SD detail OFFcameras connected to the MSU can be stored on these
switch is lighted.cards or the data can be loaded from the cards into the
SKIN ZEB: Skin tone area zebracamera.
This is used to set whether to apply the
zebra pattern to the areas where coring is=RESET
applied as the skin tones to the Y signals inThis is used to reset the CPU that operates the main unit.
the PM output.Under normal circumstances, refrain from touching it.
PHASE:Skin tone area phase
This is used to move the areas to be>ALARM
recognized as the skin tones in the range of
This lights when optical transmission is not proceeding
153 to 93 along the Q axis on the color
satisfactorily or when a problem has occurred in the
vector display.
camera, CCU.
WIDTH:Skin tone area width
This is used to widen the areas to be
recognized as the skin tones in the range of
1 to 20 along the I axis on the color vector
display.
10 |
ACEC
PANASONIC
