4) Press [START] key.
SIMULATION 48-1
MAGNIFICATION ADJUSTMENT. SELECT 0-7, AND PRESS START.SIMULATION 48-5
0.TRAY SELECT 1 1.PRINT STARTMOTOR SPEED ADJUSTMENT. SELECT 0-5, AND PRESS START.
2.MAGNIFICATION 10020.MIR(220) 50 1.MIR(169) 50
3.CCD(MAIN) 50 4.CCD(SUB) 502.MIR(110) 50 3.MIR(55) 50
0
5.SPF(MAIN) 50 6.SPF(SUB) 50 7.CIS(MAIN) 504.SPF(220) 50 5.SPF(110) 50
Select other than 0 - 2,
and press [START] key.
Press [CUSTOM SETTINGS] key.Select other than 0 - 5, and Press [START] key, or press
press [START] key.[CUSTOM SETTINGS] key.
SIMULATION 48-1
MAGNIFICATION ADJUSTMENT. INPUT VALUE 0-99, AND PRESS
SIMULATION 48-5
START.
SCAN MOTOR SPEED ADJUSTMENT. INPUT VALUE 0-99, AND
4.CCD(SUB)50
PRESS START.
0.MIR(220)
50
Select 1, and Press [START] key. Press [CUSTOM SETTINGS] key,
press [START] key.
or terminate copying.
SIMULATION 48-1
MAGNIFICATION ADJUSTMENT. NOW COPYING.
48-6
PurposeAdjustment
Press [START] key, or
Select 0, and press [START] key.press [CUSTOM SETTINGS] key.FunctionHSYNC cycle adjustment
(Purpose)
SIMULATION 48-1ItemPicture quality
MAGNIFICATION ADJUSTMENT. SELECT 1-15, AND PRESS START.
Operation/Procedure
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4(Adjustment mode selection)
5.BPT 6.LCC1) Select the number corresponding to the HSYNC cycle to be1
(ABOVE+10: DUPLEX MODE)
adjusted with 10-key. (Select one of 3.)
2) Press [START] key.
Select 2, and Press [START] key, or
press [START] key.press [CUSTOM SETTINGS] key.Set
ItemDefault
range
SIMULATION 48-10 TRAY SELECTPaper feed tray selection--
MAGNIFICATION ADJUSTMENT.1 COPY STARTCopy START (Default)--
(MAGNIFICATION)2 MAGNIFICATION Print magnification ratio25 - 400-
INPUT 25-400(%)1003 CISCIS HSYNC cycle40 - 6050
(HSYNC cycle adjustment)
1) Select the number corresponding to the HSYNC cycle to be
48-5
adjusted with 10-key. (Select one of 3.)
PurposeAdjustment
2) Press [START] key.
FunctionUsed to adjust the copy magnification ratio in the
3) Enter the HSYNC cycle adjustment value with 10-key.
(Purpose)sub scanning direction.
4) Press [START] key.
SectionOptical (Image scanning)
When the [START] key is pressed, copying is performed and
ItemPicture quality
the adjustment value is set simultaneously.
Operation/Procedure
Normal displayNOW COPYING.
When the sub scanning direction image magnification ratio adjust-
ment with SIM 48-1 cannot provide a satisfactory result if a differ-ERROR displayDoor openDOOR OPEN.
ent magnification ration is set and a copy is made, perform thisJamJAM
simulation.Paper emptyPAPER EMPTY.
When there is an error in the copy magnification ratio in reduction(Copy condition setting in this simulation)
copy, change the adjustment value of the high speed mode. When
To select paper (paper feed tray), perform the following proce-
there is an error in the copy magnification ratio in enlargement
dures.
copy, change the adjustment value of the low speed mode.
1) Enter 0 with 10-key.
1) Select the number corresponding to the adjustment mode with
2) Press [START] key. (The mode is changed to the paper feed
10-key.
tray selection mode.)
2) Press [START] key.
3) Enter the number corresponding to the paper feed tray of the
3) Enter the copy adjustment value with 10-key.
selected paper with 10-key. (Select one of 1 - 5.)
The scanner/SPF motor rotation sped adjustment value is
4) Press [START] key. (The paper feed tray is selected.)
entered.
1TRAY1TRAY1
Set
ItemContentDefault2TRAY2TRAY2
range
3TRAY3TRAY3
0 MIR (220) Mirror motor (220mm/sec)0 - 9950
4TRAY4TRAY4
1 MIR (169) Mirror motor (168.7mm/sec)
5BPTManual feed
2 MIR (110) Mirror motor (110mm/sec)
3 MIR (55)Mirror motor (55mm/sec)When the total of the above set value (1 - 5) and 10 is entered, the
mode is changed to the duplex mode.
4 SPF (220) SPF motor (220mm/sec)
5 SPF (110) SPF motor (110mm/sec)
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 52 |
ACEC
SHARP
