CodeCode
Function (Purpose)Function (Purpose)
Main SubMain Sub
4618Used to adjust the gamma (density gradient) in 536Used to adjust the DSPF width detection level.
the copy mode.7Used to enter the SPF width detection adjustment
19Used to set the auto mode operation value.
specifications in each mode (copy, scan, FAX).8Used to adjust the document scan start position.
20Used to adjust the copy density correction in the (Used to adjust the scanner scan position in the
SPF copy mode for the document table copy SPF mode front scan.)
mode. The adjustment is made so that the copy 551Used to set the specifications of the engine
density becomes the same as that of the control operations. (PCU PWB)
document table copy mode.2Used to set the specifications of the scanner
21Used to adjust the scanner exposure level in all control operations. (Scanner control PWB)
the scanner modes.3Used to set the specifications of the controller
22Used to adjust the scanner exposure level in the operations. (MFP control PWB)
normal text mode.561Used to transfer the MFP controller data. (Used to
23Used to adjust the scanner exposure level in the repair the PWB.)
fine text mode.601Used to check the MFP control (DRAM)
24Used to adjust the scanner exposure level (in the operations (read/write).
super fine text mode).611Used to check the operation of the scanner (write)
25Used to adjust the scanner exposure level in the unit (LSU).
ultra fine text mode.2Used to adjust the laser power (absolute value) in
27Used to adjust the gamma (density gradient) of the copy mode.
the network scanner mode.3Used to adjust the laser power (absolute value) in
31Used to adjust sharpness of the copy mode.the FAX mode.
39Used to adjust sharpness of the FAX mode.4Used to adjust the laser power (absolute value) in
45Used to adjust the image density in the FAX the printer mode.
mode (600dpi).621Used to format the hard disk. (Only in the model
46Used to adjust sharpness of the scanner mode.with a disk installed)
481Used to adjust the copy magnification ratio (in the 2Used to check the operation of the hard disk
main scanning and the sub scanning directions).(read/write). (Only in the model with a disk
5Used to adjust the copy magnification ratio in the installed) (Partial check)
sub scanning direction.3Used to check the operation of the hard disk
6HSYNC cycle adjustment(read/write). (Only in the model with a disk
501Used to adjust the copy image position and the installed) (All areas check)
void area (image loss) adjustment on print paper 6Used to check the operations of the hard disk.
in the copy mode. (The similar adjustment can be (The self diag operation of the SMART function is
performed with SIM 50-5 and 50-2 (Simplified executed.) (Only in the model with a disk
method).) (Document table mode)installed)
2Used to adjust the document scan position, the 7Used to check the operations of the hard disk.
image print position, and the void area (image (The result of the self diag operation of the
loss). (Simple adjustment) (This adjustment is the SMART function is printed out.) (Only in the
simple method of SIM 50-1.) (Document table model with a disk installed)
mode)8Used to format the hard disk (the system area
5Used to adjust the print image position and the excluded). (Only in the model with a disk
void area (image loss) on print paper. installed)
(Adjustment as the print engine) (This adjustment 10Used to delete a job complete list (also to delete
is reflected on all the FAX/printer/copy modes.)job log data) (Only in the model with a disk
6Used to adjust the copy image position and void installed)
area (image loss) on print paper in the copy 11Used to delete document filing data. (The
mode. (The similar adjustment can be performed management area (standard folder, user folder) is
with SIM 50-7 (simple method).) (SPF mode)cleared.) (Only in the model with a disk installed)
7Used to adjust the copy image position and void 631Used to check the result of shading correction.
area (image loss) on print paper in the copy (The shading correction data are displayed.)
mode. (The similar adjustment can be performed 2Used to execute shading.
with SIM 50-6.) (SPF mode)7Used to adjust the white plate scan start position
10Used to adjust the print image off-center position. for shading. (Document table mode)
(Adjusted separately for each paper feed 641Used to check the operation of the printer section
section.)(self-print operation), (The print pattern, the paper
12Used to adjust the scan image off-center position. feed mode, the print mode, the print quantity, and
(Adjusted separately for each scan mode.)the density can be optionally set.)
27Used to adjust the image loss of the scan image 651Used to adjust the touch panel (LCD display
in the FAX/scan mode.section) detection position.
512Used to adjust the contact pressure of paper on 2Used to check the result of the touch panel (LCD
the resist roller of each section (each paper feed, display) detection position adjustment. (The
duplex feed and SPF paper feed of the copier). coordinates are displayed.)
(This adjustment is required when the print image 661Used to change and check the FAX soft switch
position variations are considerably great or when functions. (Used to change and check the
paper jams occur frequently.)functions provided for the FAX soft switches.)
(Only when FAX is installed)
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 5 |
ACEC
SHARP
