AR-151E
[4] USER PROGRAM
The conditions of factory setting can be changed according to the use conditions.
Functions which can be set with the user program
FunctionContentsFactory setting
lWhen a certain time is passed after completion of copying, this function returns to the initial state
Auto clear timeautomatically. The time to reach the initial state can be set in the range of 30 sec to 120 sec by60 sec
the unit of 30 sec. This function can be disabled.
lWhen the copier is left unused with the power ON, the power consumption is automatically reduced
to about 40Wh/H (* Note).
The time to start this function can be set in the range of 30 sec to 90 sec by the unit of 30 sec.
PreheatThis function cannot be disabled.90 sec
lWhen this function is operated, the pre-heat lamp on the operation panel lights up.
To return to the initial state, press any key on the operation panel. (When the COPY button is
pressed, a copy is made after returning to the initial state.)
lWhen the copier is left unused with the power ON, the power consumption is automatically reduced
to about 18Wh/H (* Note). The time to start this function can be set in the range of 2 min to 120
min.
Auto shut off timer5 min
lWhen this function is operated, all the lamps except for the pre-heat lamp on the operation panel
turn off.
To return to the initial state, press the COPY button.
Stream feedingOnly models with SPF.Cancel
Auto shut offlUsed to set or cancel this function.Set
*Note: The power consumption values in preheat and auto shut off may be varied depending on the use conditions.
Setting the power save modes, auto clear time,Function nameFunction code
and stream feeding modeAuto clear time1
1) Press and hold down the light ( ) and dark ( ) keys simul-
taneously for more than 5 seconds until all the alarm indicatorsPreheat2
( , , and ) blink and "- -" appears in tAuto shut off timerhe display.3
2) Use the left copy quantity ( ) key to select a user pStream feedingrogram num-4]
ber (1: auto clear time, 2: preheat mode, 3: auto power shut-off
timer, 4: stream feeding mode, 5: auto power shut-off mode). TheAuto shut off5
selected number will blink in the left side of the display.
[Cancel]If a wrong code is entered, press the clear key and enter the
correct function code.
* SPF only
* The remaining toner quantity is displayed by pressing the % key for 5 sec before entering a program code in the user simulation mode.
3) Press the print ( ) key. The entered program number will be steadily lit and the currently p sreoglercatmed w paillr bliameternk number for the
on the right side of the display.
4) Select the desired parameter using the right copy quantity ( ) key. The entered parameter nuthem dberis wplailyl. blink on the right of
FunctionFunctionFunctionFunctionFunction
Set codeSet codeSet codeSet codeSet code
namenamenamenamename
0 (Cancel)0 (30 sec)0 (2 min)*0 (Cancel)0 (Cancel)
1 (30 sec)1 (60 sec)*1 (5 min) 1 (Setting) *1 (Setting)
Auto clear*2 (60 sec) PreheatAuto shutStreamAuto shut*2 (90 sec)2 (15 min)
timeoff timerfeedingoff
3 (90 sec)3 (30 min)
4 (120 sec)4 (60 min)
5 (10 sec)5 (120 min)
* : Factory setting
5) Press the print ( ) key. The right-hand number in the display will be steadily lit and the entered value will be stored.
Note: To change the setting or to set another mode, press the clear ( ) key. The copier will return to step 2).
6) Press the light ( ) or dark ( ) key to return to the normal copy mode.
4 � 1 |
ACEC
SHARP
