CUC 2058 D / 2059 DAllgemeiner Teil / General Section
6.2 OSD Position
3. Picture Settings
Call up the dialog line "OSD" with button "6" via "DIALOG CENTER"
Basic Adjustment�> "SERVICE" �> Service Code "8500".
Call up the picture settings menu with the red button (eye). Via theWith the 3 4 buttons it is possible to shift the on screen display in the
menu guide it is possible to change the contrast, picture sharpness andhorizontal or vertical direction and to store this position "with mem.".
tint (only NTSC sources).6.3 Hotel Mode
The analog values for contrast, picture sharpness and tint are stored
automatically when leaving the menu.6.3.1 Activating the Hotel Mode
Call up the dialog line "Hotel" with button "6" via "DIALOG CENTER"
4. Sound Settings�> "SERVICE" �> Service Code "8500".
With activated "Hotel Mode":
4.1 Sound Switching:- it is no longer possible to call up the "DIALOG CENTER" menu with
Call up the sound settings menu with the blue button (ear). Differentbutton "6".
types of sounds are available dependent on the TV standard:- the last volume setting is stored as the maximum level possible.
- "Mono": in the case of pure mono transmissions
6.3.2 Deactivating the Hotel Mode
- "Mono A / Mono B": in the case of 2-channel sound transmissionsDepress and hold button "6" on the Remote Control while switching the
- "Stereo / Mono": in the case of poor stereo sound quality, the sound
TV set on with the mains switch. Under the "SERVICE" menu switch
can be switched over to monothe Hotel Mode off.
- "Stereo / Analog"
- "Stereo A / Stereo B / Analog"6.4 Deactivating the Protection Circuit
The forced-mono, balance, bass, treble and similar values are storedDepress and hold button "6" on the Remote Control while switching the
automatically when leaving the menu.TV set on with the mains switch. As long as the Service Menu is
displayed the protection circuit of the TV set is not evaluated on video
4.2 Headphone Sound Switching
Call up the sound settings menu with the blue button. Dependent on theprocessor IC34015-(50).
TV standard, different settings are possible for the headphones:
- "Mono A / B", independent of the loudspeakers7. Setting the Analog Values
- "Stereo A / Stereo B / Analog", independent of the loudspeakers
With all other options, separate selection of the sound for the head-
MaximumOptimum
phones and loudspeakers is not possible.
Brightness6332
Colour contrast6340
5. Open Service Settings
Black/white contrast6348
Volume6330
5.1 Maximum Programme Number (reversing point)
Call up the programme number which is to be the highest selectableHeadphone volume6350
Tint6332
programme position. With button "6" select the dialog line "MANUAL
TUNING" via the "DIALOG CENTER". Following the menu guide, enterBass2515
"C 00" in the dialog line channel. Confirm with "OK" and terminate theTreble2518
menu. After this setting only those programme positions can beSharpness 5 2
selected with the "P+/P-" buttons in Programme Mode which are lower
than the "C 00" position.
The analog values are stored automatically:
5.2 Forced Chroma Switchingafter about 8 seconds,
Call up the dialog line "Color" via "DIALOG CENTER" �> "SERVICE"on switching to Standby mode,
with button "6". With the buttons 3 4 it is possible to force the automaticon switching over from TV to AV mode,
chroma standard switching function into "PAL" or "NTSC" on a per-on changing the individual AV settings.
programme basis under poor reception conditions.
Having stored the minimum volume level the volume indicator bar is
5.3 Switching off the Blue Screen Backgrounddisplayed for about 10 seconds when switching the TV receiver on.
Call up the dialog line "Blue Screen" via "DIALOG CENTER" �>
With "AUX" �> "OK" it is possible to re-set the optimum values for
"SERVICE" with button "6". When this function is set to "off" the bluepicture and sound.
background is switched off (e.g. when the aerial signal is missing).
The optimum values are read out from EEPROM IC82005.
5.4 Black Screen when Changing the Programme
Call up the dialog line "Black Screen" via "DIALOG CENTER" �>8. Audio / Video Connectors
"SERVICE" with button "6". When this function is set to "on" the screen
is blanked when changing the programme.Re-recording possibilities:
AV 1�>AV 2 (EURO-AV1 �> EURO-AV2 with 2 AV sockets)
6. Service Settings for the DealerAV 2�>AV 1 (EURO-AV2 �> EURO-AV1 with 2 AV sockets)
AV 3�>AV 1 (Camera �> EURO-AV1 with 2 AV sockets)
6.1 Service Menu
Call up the Service Menu with button "6" via "DIALOG CENTER"Re-recording is activated automatically by selecting button "0/AV" of
the source.
�> "SERVICE" �> Service Code .
Having entered the code number "8500" the dealer can change the
Securing a re-recording:
following settings under menu guide:A re-recording is secured by selecting the source with button "0 /AV"
- GEOMETRY
�> button "AUX" �> button "0/AV", indication "copy on". The pro-
- WHITE ADJUSTMENTgramme can be changed. The securing function can be cancelled by
- AGCrepeating this sequence: "Copying off".
- OSD horizontal
- OSD verticalNotes:
- Hotel- Should all video signal paths be in use on selection of AV because
- TubeCopy is active for example, this situation is identified and the TV
- Cut-off alignswitches over to the next technically possible AV position.
- Overscan- The blue screen background does not appear in all AV settings.
- NTSC 3,6
Alignment: page 2-3
GRUNDIG Service1 - 29 |
ACEC
GRUNDIG
