TO PLAY A DVD OR LD RECORDED IN
RECORDING AN AUDIO SOURCE
DOLBY DIGITAL OR DTS SURROUND
This receiver is equipped with the Dolby Digital decoder and
DTS decoder, and has the DIGITAL IN (both OPTICAL and
COAXIAL) terminals. When a DVD or LD player is connected to
the DIGITAL IN terminal of the receiver, you can enjoy theater-
quality audio right in your home when playing discs recorded in
Dolby Digital surround or DTS surround.
Before operation
Y Check that the TAPE MONITOR is not selected. If the TAPEBASIC OPERATIONS
MONITOR is selected, press the TAPE MONITOR button so
that OTAPE OFF� appears on the display.
Y When connecting an LD player equipped with the AC-3 RF1Select the program source to be recorded.
OUT terminal, use an RF demodulator unit. Also connect theTurn the FUNCTION.
analog AUDIO OUT terminals of the LD player to the receiver
to play all the sources. For further information, ref2Set the tape decer to thek or MD recorder to the recording
instructions of the LD player.mode.
1 Turn the FUNCTION to select the VIDEO 1 (VIDEO3 Start the selected program source.
2 or VIDEO 3) and press the DIGITAL/ANALOG/
BAND button repeatedly until ODIGITAL� isTo monitor recorded sound during recording (when the
displayed.connected tape deck is a three-head system)
Press the TAPE MONITOR button.OTAPE ON � appears on the
display for four seconds, and then the source name selected in
step 1 comes back on. To cancel the tape monitor, press it again
so that OTAPE OFF� appears.
NOTE
The DVD (LD) player connected to the OPTICAL (COAXIAL)
Y Any sound control system has no effect on recording (see
DIGITAL IN terminal is selected as a source.
page 8).
2 Start playing the DVD (LD) recorded in DolbYInput sound through the DIGITyAL IN terminals cannot be
Digital surround or DTS surround.recorded. When recording the sound from the DVEnEnEnEnEnD, CD, MD
YThe ODOLBY DIGITAL� indicator will light on the display whenor LD player, connect the analog AUDIO OUT terminals of
the bit stream of the Dolby Digital surround comes in the unit.the player to the corresponding AUDIO IN terminals of the
receiver.
The sound will be recorded in 2 ch stereo.EEEEE (Espan(Espan(Espan(Espan(Espanooooo
Y When recording audio sources by the MD recorder connected
to the VIDEO 1/DVD/MD AUDIO OUT terminals, the selected
video source (see page 11) should be V2 or V3. Recording
cannot be done while the V1 (VIDEO 1) is selected andFFFFF (Franç (Franç (Franç (Franç (Françaaaaa
To select the Dolby Digital surround mode according to your
displayed on the window.
speakers, see OSELECTING DOLBY SURROUND � on page 15.
Y Input sound from the tape deck connected to the TAPE
YThe Odts� indicator will light on the display when the bit stream
MONITOR IN terminals cannot be recorded.
of the DTS surround comes in the unit.
To select the DTS surround mode according to your
speakers, see OSELECTING DTS SURROUND � on page 19.
NOTE
YWhile the TAPE MONITOR is selected and the TAPE MONITOR
indicator turns red, ODIGITAL� cannot be selected.
YWhen headphones are plugged in, the Dolby Digital surround
mode or DTS surround mode is automatically changed to
O2chSTEREO � and the O2CH DOWNMIX � indicator lights on the
display.
Even if the SURROUND button is pressed while the
headphones are plugged in, the mode cannot be changed.
YThis unit supports input signals of the Dolby Digital surround
bit stream, DTS surround bit stream and linear PCM whose
sampling frequency is 32 kHz, 44.1 kHz, 48 kHz and 96 kHz.
YWhen connecting some DVD players to the receiver through
the DIGITAL IN terminals, noise may be heard in the DVD
operation: e.g. searching a disc, skipping a chapter.
ENGLISH 12 |
ACEC
AIWA
