AVR45 om (G).Eng,Fr 4/16/99 11:41 AM Page 28
Programming the Remote
28
The AVR45 is equipped with a powerful3. Press and hold both the Device7. If a code cannot be entered to turn the
remote control that will control not onlyControl Selectorbfor the typeunit off, if the code for your product
the receiverOs functions, but also most CDof product to be entered (e.g., VCR,does not appear in the tables in this
players and cassette decks manufacturedTV) and the Mutebutton d at themanual, or if not all functions oper-
by Harman Kardon. For increased flexi-same time. Hold both buttons untilate properly, try programming the
bility, the remote also contains the codesthe red light under the button staysremote with the Auto Search Method.
for most popular brands of audio andlit. Note that the next step must take
video equipment, including CD players,place while the red light is on, and itAuto Search Method
cassette decks, TV sets, cable boxes, VCRs,must begin within 20 seconds after
satellite receivers and other home-theaterthe light illuminates.If the unit you wish to include in the
equipment. Once the AVR45Os remote isAVR45Os remote is not listed in the code
programmed with the codes for the pro-4. Point the AVR45Os remote towards thetables in this manual, or if the code does
ducts you own, it is possible to eliminateunit to be programmed, and enter thenot seem to operate properly, you may
most other remotes and replace themfirst three-digit code number using thewish to program the correct code using
with the convenience of a single, backlitNumericbuttons l. If the unitthe Auto Search method as shown below.
universal remote control.turns off, the correct code has been
entered. Press the Device Control1. Turn on the unit that you wish to
Programming the RemoteSelectorbagain, and note thatinclude in the AVR45 remote.
the red light will flash twice to confirm
As shipped from the factory, the remote the entry before going dark.2. Press the Device Control Selector
is fully programmed for all AVR45 func-bfor the type of product to be
tions, as well as those of most Harman5. If the device to be programmed inentered (e.g., VCR, TV) and the Mute
Kardon CD changers, CD players and cas-does NOT turn off, continue to enterbutton d at the same time. Hold
sette decks. In addition, by following onethe three-digit code numbers untilboth buttons until the red light under
of the methods below, you may programthe equipment turns off. At this point,the button stays lit. Note that the next
the remote to operate a wide range ofthe correct code has been entered.step must take place while the red
devices from other manufacturers.Press the Device Control Selectorlight is on, and it must begin within
bagain, and note that the red20 seconds after the light illuminates.
Direct Code Entry
light will flash twice to confirm the
entry before going dark.3. Point the AVR45 remote towards the
This method is the easiest way tounit to be programmed, and press
program your remote to work with6. Try all of the functions on the remoteand hold the Surround Mode
different products.Selectoryor the Sleepbutton
to make certain that the product
operates. Keep in mind that many`. This will send out a series of
1. Use the tables in the following pagescodes from the remoteOs built-in data
manufacturers use a number of dif-
to determine the three-digit code orferent combinations of codes, and itbase, with each flash of the red light
codes that match both the productunder the Device Control Selector
is a good idea to make certain that
type (e.g., VCR, TV), but also thenot only the Power control works, butindicating that a code has been sent.
specific brand name. If there is moreWhen the device to be programmed
the volume, channel and transport
than one number for a brand, maketurns off, IMMEDIATELY release the
controls, as appropriate. If all func-
note of the different choices.tions do not work properly, you maySurround Modeor Sleepbutton.
need to use a different remote code.
2. Turn on the unit you wish to program
into the AVR45 remote. |
ACEC
HARMAN KARDON
