HARMAN KARDON AVR5 Instruction Manual

AVR5 om (e) 2/5/99 10:38 AM Page 24
Operation
24
4. Stations may also be tuned directly the station frequency indication begins toClearing Preset Stations
by pressing the Direct button ?, andincrease. Release the button and note thatUnwanted preset stations may be erased
then pressing the Numeric KeysVthe tuner will search the entire FM band,from the unitOs memory to make it easier
that correspond to the stationOs frequency.and stop briefly at each station that hasto tune only those stations you want.
The desired station will automatically acceptable signal strength. The AVR5 will
be tuned.automatically assign a preset number toTo remove a preset station from the
each station, and then search for the nextAVR5Os tuner memory, first tune to the
NOTE: When the FM reception of astation. The automatic scan process willstation using the Preset Scanbutton
station is weak, audio quality will bestop when all 30 preset memory locations%żon the front panel or remote, or
increased by switching to Mono mode have been filled or the entire FM band hasby entering the preset number directly,
by pressing the FM Mode button &been scanned three times.using the Numeric KeysV.
Iuntil the STEREOindicator goes out.
NOTE: Using the automatic tuning modeWhen the preset station to be removed
Preset Tuningin areas with more than 30 FM stationshas been tuned, first press the Memory
Up to 30 stations may be stored in thewill completely fill the preset memories,button >. The MEMO and PRESET
AVR5Os memory for easy recall using theand over-write any previously memorizedindicators in the Information Display will
front panel controls or the remote.presets for either AM or FM stations.flash, and the actual preset number will
disappear from the display. Next, press the
To enter a station to the memory, firstTIP: The automatic scan process Clearbutton �within five seconds.
tune the station using the steps outlinedmay enter stations that you do not
above. Then:wish to retain in the memory, or it The preset station will be removed from
1. Press the Memory button > on may enter a station on more than onethe memory, and the action will be con-
frequency if the signal is too strong.firmed by the brief appearance of the
the remote. Note that MEMO and PRESETThese unwanted stations may beword CLEARand the preset number
indicators will illuminate and flash in
the Information Display.removed from the memory using thelocation in the Information Display. That
Preset Clear function outlined below.memory location will now be empty, and
you may program a different station to
2. Within five seconds, press theRecalling Preset Stationsthat location, or leave it empty.
Numeric KeysVcorresponding to the
location where you wish to store this sta-Y To manually select a station previously
entered in the preset memory, press theTape Recording
tionOs frequency.Numeric KeysVthat correspond to
the desired stationOs memory location.In normal operation, the audio or video
3. Repeat the process after tuning anysource selected for listening through the
additional stations to be preset.
Y To manually tune through the list ofAVR5 is sent to the record outputs.
stored preset stations one by one, pressThis means that any program you are
Auto Preset
Y Preset stations may also be programmedthe Presetbuttons ^  on the frontwatching or listening to may be recorded
panel or remote.simply by placing machines connected
automatically for the FM band. To auto-to the outputs for Tape Monitor? or
matically enter each station that may beY To automatically scan through theVideo Oneain the record mode.
tuned with acceptable quality into the
AVR5Os preset memories, first select the FMstations entered in the preset memory,
press the Preset Scanbutton %ż on
band. Next, press and briefly hold thethe front panel or remote. The tuner will
Auto Presetbutton Xuntil the MEMOrun through the list of preset stations,
and PRESET indicators begin to flash, and
stopping for five seconds at each one.
Press the button again to stop the scan at
your desired station.