AVR510 harman/kardon
Main Remote Control Functions
t Direct Button: Press this button whenory. When some source devices, such as CD35TV/Video Button:This button does not
the tuner is in use to start the sequence forplayers, VCRs and cassette decks, are selectedhave a direct function on the AVR 510, but
direct entry of a stationOs frequency. After press-using the device Input Selectors e, thesewhen used with a compatibly programmed
ing the button, simply press the properbuttons may function as Chapter Step or TrackVCR, DVD or satellite receiver that has a
Numeric Keys r to select a station. (SeeAdvance.OTV/Video� function, pressing this button will
page 30 for more information on the tuner.)switch between the output of the player or
28Clear Button:Press this button to clear
receiver and the external video input to that
u Tuning Up/Down: When the tuner is inincorrect entries when using the remote to player. Consult the OwnerOs Manual for your
use, these buttons will tune up or down throughdirectly enter a radio stationOs frequency.specific player or receiver for the details of how
the selected frequency band. If the Tuner Modeit implements this function.
button s@ has been pressed so that the29Memory Button:Press this button to
AUTO indicator X is illuminated, pressing andenter a radio station into the AVR 510Os preset36SPLIndicator Select:This button acti-
holding either of the buttons for three secondsmemory. Once the MEMORY indicator U
vates the AVR 510Os EzSet function to quickly
will cause the tuner to seek the next station withflashes, you have five seconds to enter a presetand accurately calibrate the AVR 510Os output
acceptable signal strength for quality reception.memory location using the Numeric Keys
levels. Press and hold the button for three sec-
When the AUTO indicator X is NOT illumi-r. (See page 31 for more information.)onds and then release it. Note that the test
nated, pressing these buttons will tune stations
tone will begin circulating, and the
in single-step increments. (See page 30 for more30Delay/Prev Ch.:Press this button to
information.)begin the process for setting the delay timesProgram/SPL Indicator c will change col-
ors. During this sequence, EzSet will automati-
used by the AVR 510 when processing surroundcally adjust the output levels for all channels
v OSD Button: Press this button to activate
sound. After pressing this button, the delayuntil they are equal, as shown by the
the On Screen Display (OSD) system used to settimes are entered by pressing the Set button
up or adjust the AVR 510Os parameters.Program/SPL Indicator lighting green for
p and then using the �/U buttons n toeach channel. Press this button again when the
change the setting. Press the Set button p
w Macro Buttons: Press these buttons adjustment is complete to turn off the test
to store or recall a OMacro�, which is a again to complete the process. (See page 21 fortone. (See page 23 for more information on
more information.)
preprogrammed sequence of commands EzSet.)
stored in the remote. (See page 37 for more
31�Button:Press this button to change a
information on storing and recalling macros.)376-Ch.Direct Input:Press this button
setting or selection when configuring many of theto select the component connected to the
x Transport Controls: These buttons doAVR 510Os settings.6-Channel Direct Input ? as the source.
not have any functions for the AVR 510, but
they may be programmed for the forward/32Speaker Select:Press this button 38Mute:Press this button to momentarily
reverse play operation of a wide variety of CDto begin the process of configuring the silence the AVR 510 or TV set being controlled,
or DVD players, and audio or video cassetteAVR 510Os bass management system for usedepending on which device has been selected.
recorders. (See page 38 for more information.)with the type of speakers used in your system.When the AVR 510 remote is being programmed
Once the button has been pressed, use theto operate another device, this button is pressed
y Skip Up/Down Buttons: These buttons�/Ubuttons nto select the channel youwith the Input Selector button e to begin
do not have a direct function with the AVR 510,wish to set up. Press the Set button p andthe programming process. (See page 36 for
but when used with a compatibly programmedthen select another channel to configure.more information on programming the remote.)
CD or DVD changer they will change the discWhen all adjustments have been completed,
currently being played in the changer.press the Set button p twice to exit the 39EzSetSensor Microphone:The sensor
settings and return to normal operation. (Seemicrophone for the EzSet microphone is behind
z Disc Skip Buttons: These buttons havepage 22 for more information.)
no direct function for the AVR 510, but they arethese slots. When using the remote to calibrate
speaker output levels using EzSet, be sure that
often used when the remote is programmed to33Multiroom:Press this button to activateyou do not hold the remote in a way that cov-
operate a CD or DVD changer to change the
the multiroom system or to begin the process ofers these slots. (See page 23 for more informa-
discs in the changer. (See page 38 for more
changing the input or volume level for the sec-tion on using EzSet.)
information on using the remote with otherond zone. (See page 35 for more information on
devices.)
the multiroom system.)40Light Button:Press this button to acti-
vate the remoteOs backlight for ease of use in
` Preset Up/Down: When the tuner is
34Volume Up/Down:Press these buttons todarkened rooms.
in use, press these buttons to scroll through the raise or lower the system volume.
stations programmed into the AVR 510Os mem-
13 MAIN REMOTE CONTROL FUNCTIONS |
ACEC
HARMAN KARDON
