AVR 7200 OM 1/27/03 4:46 PM Page 12
AVR7200 harman/kardon
MAIN REMOTE CONTROL FUNCTIONS
IMPORTANT NOTE: The AVR 7200Os remote may 7 Logic 7 Mode Select Button: Press this buttonE Digital Select Button: Press this button to assign
be programmed to control up to eight devices,to select from among the available Logic 7 surroundone of the digital inputs j32 &( to a source. (See
including the AVR 7200. Before using the remote,modes. (See page 29 for the available Logic 7page 30 for more information on using digital inputs.)
it is important to remember to press the Inputoptions.)F Set Button: This button is used to enter settings
Selector Button 3 that corresponds to the unit8 Direct Button: Press this button when the tunerinto the AVR 7200Os memory. It is also used in the
you wish to operate. In addition, the AVR 7200Osis in use to start the sequence for direct entry of a sta-setup procedures for delay time, speaker configuration
remote is shipped from the factory to operate the
AVR 7200 and most Harman Kardon CD or DVDtionOs frequency. After pressing the button, simplyand channel output level adjustment.
players and cassette decks. The remote is also press the proper Numeric Keys A to select a sta-G Transport Play Buttons: These buttons have no
capable of operating a wide variety of other productstion. (See page 32 for more information on the tuner.)direct function on the AVR 7200, but they are used
using the control codes that are part of the remote.9 Clear Button: When programming the remote when the remote is programmed for a compatible
Before using the remote with other products, followor using the EzSet feature, press this button to cancel DVD, CD or tape player. Pressing these buttons will
the instructions on pages 38 � 40 to program thethe current function.When using the remote to enter transmit a forward- or reverse-play command,
proper codes for the products in your system.frequencies for direct tuner access, press this button according to the capabilities of the player being
to clear previous entries.controlled. In the factory default setting, these buttons
It is also important to remember that many of the are programmed for Harman Kardon DVD players so
buttons on the remote take on different functions,A Numeric Keys: These buttons serve as a ten-
depending on the product selected using the Devicebutton numeric keypad to enter tuner preset positions.that you may control a compatible player without
Control Selectors.The descriptions shown here primarilyThey are also used to select channel numbers whenhaving to switch devices.
detail the functions of the remote when it is used toTV, Cable or SAT has been selected on the remote, orH Volume Up/Down Buttons: These controls
operate the AVR 7200.to select track numbers on a CD, DVD or LD player,share the common disc in the lower third of the
a Power Off Button: Press this button to placedepending on how the remote has been programmed.remote. To raise the volume, press the button marked
the AVR 7200 or a selected device in the StandbyThese buttons are also used to enter letters and num-?by pressing towards the top of the remote.To lower
bers when renaming devices in the LCD Informationthe volume, press the button marked ¤ by pressing
mode. Note that this will turn off the main room Display. (See page 45 for more information on renam-towards the bottom of the remote. The ?/? buttons
functions, but if the Multiroom system is activated,ing devices and keys.)on the left and right sides of this disc change channels
it will continue to function.up or down when the TV, cable box or satellite Input
B Tuning Mode: Press this button when the tuner
1 Power On Button: Press this button to turn onis in use to select between automatic tuning and manualSelectors 3 have been pressed.
the power to a device selected by first pressing one oftuning.When the button is pressed so that MANUALI Transport Fast-Play/Scan Buttons: These but-
the Input Selectors 3.TUNING appears in the Lower Display Line B,tons have no direct function on the AVR 7200, but
2 LCD Information Display: This two-line screenpressing the Tuning Selector 9w will move the they are used when the remote is programmed for a
displays various information depending on the com-frequency up or down in single-step increments.Whencompatible DVD, CD or tape player. Pressing these but-
mands that have been entered into the remote.the FM band is in use, pressing this button for manualtons will transmit a fast-play forward, fast-play reverse,
tuning when a stationOs signal is weak will change toor fast-forward or -reverse scan command, according
3 Input Selectors: Pressing one of these buttonsmonaural reception. (See page 32 for more information.)to the capabilities of the player being controlled. In the
will perform three actions at the same time. First, if thefactory default setting, these buttons are preprogrammed
AVR 7200 is not turned on, this will power up the unit.m Channel Select Button: This button is used to
Next, it will select the source shown on the button asstart the process of setting the AVR 7200Os output levelswith the remote codes for Harman Kardon DVD players
the input to the AVR 7200. Finally, it will change theto an external source. Once this button is pressed, pressso that you may control a compatible player without
remote control so that it controls the device selected.the?/¤ on the Navigation Button n to select thehaving to switch devices.
After pressing one of these buttons you must presschannel being adjusted, then press the Set ButtonJ Main Transport Controls: These buttons have
the AVR Selector Button 4 again to operate theF, followed by the ?/¤ on the Navigation Buttonno direct function on the AVR 7200, but they are used
AVR 7200Os functions with the remote.n again, to change the level setting. (See page 33 forwhen the remote is programmed for a compatible
more information.)DVD, CD or tape player. Pressing these buttons
4 AVR Selector: Pressing this button will switch thewill transmit a stop (�), record (�), or pause (?)
remote so that it will operate the AVR 7200's functions. IfD Navigation Button: This single disc-like button iscommand, according to the capabilities of the player
the AVR 7200 is in the Standby mode, it will also turnused to navigate through the on-screen configurationbeing controlled. In the factory default setting, these
the AVR 7200 on.menus, to scroll through the options list and to select
choices for the various settings such as delay, speakers,buttons are programmed with the remote codes for
5 Test Button: Press this button to begin thesurround modes, digital inputs, etc. To use the button,Harman Kardon DVD players so that you may control
sequence used to calibrate the AVR 7200Os output simply press it left, right, up or down in the directiona compatible player without having to switch devices.
levels. (See page 24 for more information on calibrat-
ing the AVR 7200.)indicated by the ?¤?? icons printed on the buttonK Track Skip Up/Down Buttons: These buttons
disc. Depending on the menu being used, pressing thedo not have a direct function with the AVR 7200, but
6 DSP Surround Mode Selector: Press this button will either change the video highlight that indi-when used with a compatibly programmed CD or DVD
button to select from among the available DSP surroundcates a specific choice or it will change the optionchanger will change the track or chapter currently being
modes. (See page 29 for more information on theshown in the on-screen or front panel display. Theplayed. In the factory default setting, these buttons are
Theater, Hall and VMAx modes.) sections in this manual describing the unitOs individualprogrammed with the remote codes for Harman Kardon
features and configuration options contain specificDVD players so that you may control a compatible player
information on how the navigation controls are used.without having to switch devices.
12 MAIN REMOTE CONTROL FUNCTIONS
12 |
ACEC
HARMAN KARDON
