CONSUMPTION DATA?Rinse Hold? buttonDOOR LOCK
The laundry remains in the last rinse water
Temperature LoadWaterEnergyApprox.without progressing to the final spin cycle to The door can be opened when the ?Door Open?
SelectorProgrammeindication is on.
Programmeavoid creasing and prevent colours from
Duration
changing.
(°C)(kg)(l)(kWh)(hours : minutes)*PROGRAMME END
This option is particularly recommended for the
Cotton955.053**1.902:00
programme ?Synthetics?, ?Daily? and The remaining time is on ?0:00? and all the lights
Cotton605.0480.952:20
?Delicates?.of the programme sequence indication are off.
Cotton404.5440.602:05
This function is particularly useful if you want to
Synthetics602.5550.801:301. Turn the programme selector to the ??
postpone spinning to a later time, or if you want
Synthetics402.5550.601:20position.
to drain only.
Daily403.0450.501:002. Turn the water supply tap off.
Short303.0370.400:30Note: The programme stops to ?Rinse Hold? at the 3. Open the door and unload the machine.
Delicates401.5600.600:45time the ?Rinse Hold? light in the programme flow 4. Close the tap and leave the door ajar to allow
Wool301.0600.300:40indication is on.the drum to dry out.
Silk301.0450.300:40Terminate the ?Rinse Hold? option:
CHANGE THE PROGRAMME, OPTIONS
Prewash cycle might increase programme duration. Consumption values were measured in normalized conditions in Press the ?Rinse Hold? button again; the AFTER PROGRAMME START
compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the programme will terminate automatically with the
table in relation to the water supply pressure and temperature, the load and the type of wash.final spin cycle for the present wash programme.1. Press the ?Start/Pause? button to pause the
* The remaining time indicator can similarly deviate from the values in the table, because it takes into account the programme. The light flashes.
If you do not wish to spin the clothes, turn the
household conditions applicable at that time.
2. Select the new programme (with temperature),
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the programme selector knob to the ?Drain?
water out.programme and press the ?Start/Pause? any options and another spin speed if you want.
3. Press the ?Start/Pause? button again. The
ADD DETERGENTS, CLOSE THE DOOR SELECT ANY DESIRED OPTIONbutton again when flashing.
new programme continues at the same position
AND SELECT THE PROGRAMME?Spin Speed Reduction? button
Selecting any option the indication lights up.
where the previous programme was
Add the detergent as described in the programme When the combination of programme, Every programme has an automatic predefined
interrupted. Do not add detergent for this
table or in the chapter ?Detergents and Additives? additional options and temperature is not maximum spin speed.
programme.
in the booklet.possible, the indication lights switch off Press the button to set another spin speed.
automatically. Unsuitable combinations of CANCEL A PROGRAMME BEFORE THE END
1. Turn the programme selector knob to the If the spin speed ?0? is selected, the final
options are deselected automatically.
desired programme and temperature.spinning is cancelled but intermediate spin peaks 1. Press the ?Start/Pause? button to pause the
?Prewash? buttonremain during rinse. The water is drained out
2. The remaining time display shows the duration programme. The light flashes.
of the chosen programme (in hours and Only for heavily soiled loads (for example sand, only.2. Set the programme selector to ?Drain?. The
minutes) and after taking some seconds for granular dirt) sensible. The cycle time increases spin indicators show ?0? and the remaining
PROGRAMME START
calculating, the pilot lamp of the ?Start/Pause? approximately 15 min.
time shows ?0:02?.
button is flashing.?Intensive Rinse? buttonOpen the tap and press the ?Start/Pause? button.
3. Press the ?Start/Pause? button to start the
3. The programme sequence and the predefined More water and a longer time in rinse cycle is The pilot lamp of the ?Start/Pause? button lights drain programme.
spin speed indication corresponding to the added.up.
selected programme lights up.The indicator lamps show the sequence reached in
This option is particularly suitable for areas with
very soft water, washing baby linen and helps the programme. After starting the programme, the
people with allergies.sequence indication runs from left to right through
Wash, Rinse, Spin.
When the sequence of the programme is finished
the corresponding lamp goes out.
Whirlpool is a registered trademark of Whirlpool USA
5019 301 10165 |
ACEC
WHIRLPOOL
