Operation
$ Black balance adjustment
The black balance must be adjusted when the equipment is
Manual adjustment of black balance
used for the first time, when it has not been used for a
prolonged time, when the ambient temperature has changed1. Select the pan-tilt head system using the
significantly or when one season gives way to another.CONTROL/PREVIEW MONITOR OUT SEL button.
If the equipment is to be used under conditions which are
identical to the entered settings, no further adjustments are2. Connect a waveform monitor or color monitor to the
necessary.VIDEO/Y OUT connector on the main unit that
When the black balance is adjusted again, the previously
corresponds to the pan-tilt head system currently
entered settings will be deleted and replaced by the newselected.
conditions.
3. Press the IRIS button to establish the MANU mode (the
Automatic adjustment of black balanceIRIS buttonOs lamp now goes off), and use the
FOCUS/IRIS dial to close the lens iris.
1. Select the pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button.4. Press the R/B GAIN/PED button, and set it so that the
following item appears on the LCD panel.
2. Press the IRIS button to set the currently selected pan-
tilt head system to the AUTO mode (the IRIS buttonOsPPEEDDEESSTTAALL TTOOTTAALL ??00
lamp now comes on).RR:: ??00 BB:: ??00
5. Use the menu setting control (L) to adjust the pedestal of
3. Press the ABC button. The ABC buttonOs lamp flashes,the R (red) channel, and use the menu setting control
the lens iris is automatically stopped down, and the black(R) to adjust the pedestal of the B (blue) channel.
balance is automatically adjusted. Once the adjustment
has been performed correctly, the lamp goes off, and the6. Select the next pan-tilt head system using the
conditions set are entered in the memory.CONTROL/PREVIEW MONITOR OUT SEL button, and
The ABC buttonOs lamp will remain lighted if it was notcontinue adjusting the black balance in each system
possible for the adjustment to be performed. In thisconcerned.
case, repeat the adjustment procedure.
<Notes>
3 355 4(3) 1
O It may not be possible to adjust the black balance if
the total pedestal is too low. In this case, adjust theOPERATEOPENTELEFARGAINAUMANUTOBALIRISZOOM FOCUSAWCCONTRASTWHITELCDLAMPDEFWIPH/FEXTNDOPTIONCAMERA CONTROLPAN/TILT SET
ONA
total pedestal again, and then repeat the blackMODEBARNGTRACING MEMORY
OFFCAMBOKR/BSTART
DATA SETABCGAIN/PEDMENUOKPOINTSTART/STOPRESTORERESET
balance adjustment.INCOMATWCONTRCAMERAOL
TALLY
O The ABC buttonOs lamp goes off even if the blackCALLTR/PSET M.LOCK12345678910PRIORITYTRACING/PRESET MEMORY
CLOSEWIDENEAR12345AUX
balance adjustment was not performed correctly inLEVELIRISTRPSETCONTROL/PREVIEW MONITOR OUT SEL
TELEMEMORY11121314151617181920SPEEDUP
cases where a pan-tilt head system other than theLOCKAUMANUTOLOHIGHW
EMPTYFULL
212223242526272829130
AW-PH350 is being used.IRISIRIS
FOCUSFOCUS
31323334353637383940LR
4. Select the next pan-tilt head system using theCLOSENEAROPENFAR41424344454647484950CLOSENEAROPENFAR
WIDEDOWN
ZOOM/FOCUS/IRISPAN/TILT/FOCUS/IRIS
CONTROL/PREVIEW MONITOR OUT SEL button, andLIMITONLIMITOFF
continue adjusting the black balance in each system
concerned.
231
OPERATEOPENTELEFARIRISZOOM FOCUSWHITEAWCPAN/TILT SET
GAINAUMANUTOBALONCONTRASTLCDLAMPDEFWIPH/FEXTNDOPTIONCAMERA CONTROL
A
MODEBARNGTRACING MEMORY
CAMBABCOFFOKR/BSTPOINTARTSTART/STOPRESTORERESET
INCOMDATA SETCONTRCAMERAOLGAIN/PEDMENUOKATW
TRACING/PRESET MEMORYTALLY
CALLTR/PSET M.LOCK12345678910PRIORITY
12345AUX
CLOSEWIDENEAR
LEVEL
IRISTRPSETCONTROL/PREVIEW MONITOR OUT SELTELEMEMORY11121314151617181920SPEEDUP
AUTO
LOCKEMPTYFULLMANULOHIGHW
IRIS212223242526272829130IRIS
FOCUSFOCUS
31323334353637383940LR
CLOSENEARWIDEOPENFAR41424344454647484950CLOSENEARDOWNOPENFAR
ZOOM/FOCUS/IRISPAN/TILT/FOCUS/IRIS
LIMITONLIMITOFF
30 |
ACEC
PANASONIC
