BassLink T
CONTROLSAND FUNCTIONSTUNING BASSLINK T
BassLink T provides several controls and indica-NOTE: Depending on BassLink TOs orientation and1. Unplug the RJ11 cable that connects the8. Adjust the CROSSOVER control clockwise
tors that simplify sonic integration with virtuallylocation in a vehicle, reversing the phase may Remote Level Control to BassLink T. or counterclockwise until you hear only low-
any vehicleOs unique acoustic properties. They are(or may not) increase or decrease the amount frequency information. For example, you
located on the top control panel, as shown inof perceived upper bass being reproduced. 2. Make sure the head unit is off and its volumeshould NOT hear any vocals coming from
Figure 12.control is set to minimum. BassLink T when seated in the normal
AUTO TURN-ON: For speaker-level connections,listening position.
GAIN Control: Use this control to adjust the use this switch to activate (or deactivate)3. On BassLink TOs top panel, initially set all
relative volume (loudness) of BassLink T withBassLink TOs automatic turn-on circuit.controls to their midpoint positions, as shown9. Adjust the BASS-BOOST control clockwise
respect to the other speakers in the vehicle.in Figure 12. On BassLink TOs top panel, or counterclockwise to suit your taste.
REMOTE LEVEL CONTROL: Use this RJ11 jack initially set PHASE to 0!.
CROSSOVER: Use this control to adjust theto connect the Remote Level Control (see page 6).10.Recheck the PEAK LED to make sure itOs
amount of high-frequency information present in4. Turn on the head unit and play a favoriteflashing in time with the bass but is not lit
BassLink TOs output. A lower value means more ofPEAK LED:This indicator glows red when themusic track that has substantial bass. Set thecontinuously. If it is lit continuously, adjust
the high frequencies are filtered out. subwoofer is at maximum output. Be sure tohead unitOs volume control to 75 percent ofthe GAIN control counterclockwise until the
monitor this indicator during BassLink T setupthe total output (approximately 3 oOclock onPEAK LED only flashes.
BASS BOOST: Use this control to correct any (see Tuning BassLink T). When properly tuned,rotary controls).
perceived peak or dip in the bass response the PEAK LED should light momentarily during11.Reconnect the RJ11 cable between the Remote
(typically around 40Hz in most vehicles). Set thehigh-level bass transients. Avoid adjustments5. Adjust the GAIN control clockwise until theLevel Control and BassLink T. You may then
control to any value between �6dB and +3dB,that cause the PEAK LED to remain lit for PEAK LED (on BassLink TOs top panel) beginsuse the Remote Level Control to adjust the
according to your preference.extended periods.to flash with each bass note but doesnOt staylevel of the bass to suit your taste and/or
lit continuously.different program material.
PHASE Control: Use this switch to reverse thePOWER LED:This indicator will glow blue when
phase of BassLink TOs output with respect to itsBassLink T is operational.6. Listen to your system, making a mental NOTE: In most cases, the above steps will provide
input. Choose the position (0! or 180!) thatnote of the amount of upper bass being satisfactory tuning. However, the actual process
sounds the best.reproduced.may require several readjustments of each control,
since the settings will interact with each other.
7. Switch the PHASE control to 180! and listenIf necessary, consult your authorized Infinity
Figure 12. BassLink T control panel. again for upper bass content. There may becar audio dealer for help in tuning your system.
more upper bass, less upper bass, or no
LINE LEVELHIGH LEVELAUTO
POWERTURN ONBASS change at all. The position that provides theINPUTINPUT
GAIN CROSSOVER BOOST
++PEAKmost upper bass is correct, but choose either
LROFFAUTOsetting according to your taste.
��PHASE
REMOTELR
FUSE+BATTREMGNDLEVELCONTROL
25A0°180°
5 |