MENU SCREEN � Contents of the menus � (continued)
REMOTE menuAUDIO/VIDEO menu
ItemsSettingContentsItemsSettingContents
REM STOP SELEEUse this menu item to set the action to be performed when aAUDIO MODE48kSelect the audio sampling frequency for recording.
PBSTANDBY ON command is received via the 9 PIN REMOTE ter-32k48k : Records at 48kHz. It records in the 2-channel stereo mode.
minal or DV terminal.No audio dubbing.
EE: Sets the unit to the EE mode. (The unit will go into the STOP mode.)32k : Records at 32kHz. It records in the 4-channel mode. To per-
PB: Sets the unit to the PLAY mode. (The unit will go into the STILL mode.)form audio dubbing on CH3 and CH4 later, use this setting.
Memo
PB START0FUse this menu item to adjust the edit timing. When the remote con-
This setting is not required for DV signal input.
DELAY |troller is used, there will be a slight delay time before edit starts. To
15Frectify the time discrepancy, adjust the timing for starting playback.
0F: No compensationA.OUT ATOFFUse this menu item to enable/disable audio output from the AU-
SERCHONDIO OUT terminal during a search.
1F to 15F : Delay by the number of frames set by the user. When
this unit is connected to an editing remote controllerOFF : No output.
ON : Output
with no BUMP (synchronization) function, use this set-
ting to adjust the editing precision.
AUDIO OUT SELCH1/CH2Use this menu item to select the audio channel output from the
SYNCHRONI-OFFUse this setting to turn on/off the BUMP function when the unit isMIXAUDIO OUT terminal when playing back tapes recorded in the 32k
ZATIONONconnected to an editing remote controller.CH3/CH4mode.
OFF : No synchronizationCH1/CH2 : Outputs CH1 and CH2 audio.
ON :Execute synchronization. The editing precision is enhanced .MemoMIX: Outputs mixed audio of CH1 and CH3 and mixed au-
Please set the pre-roll time to at least 7 seconds.When it is set to the MIXdio of CH2 and CH4.
mode, noise may be pro-CH3/CH4 : Outputs CH3 and CH4 audio.
NEXT PAGEDisplay the REMOTE (2/2) menu.duced. If this occurs, pleaseMemo
set it to CH1/CH2 or CH3/
This setting can also be selected from the AUDIO OUT SEL. but-
PAGE BACKReturn to the TOP MENU.CH4.ton on the wireless remote controller.
AUDIO OUTATTUse this menu item to select the standard level for audio playback
REMOTE (2/2) menu
LEVELNORMoutput.
ItemsSettingContentsATT: Attenuates the standard level to �12db. Use this setting
when playing tapes recorded at the standard level of
CONTROLLERTYPE1-When remote control is executed via the RS-422A interface, use�12dB. The playback level is decreased by 8db.
SELTYPE7this menu item to set the type of controller connected.NORM : Sets the standard level to �20dB. Usually, this is selected.
TYPE1 : RM-G820Memo
TYPE2 : RM-G860This setting can also be selected with the AUDIO OUT LEVEL
TYPE3 : AG-A850button on the wireless remote controller.
TYPE4 : RM-450,PVE-500
TYPE5 - TYPE7 : not in useSET UPOFFUse this setting to determine whether to apply the setups to the
(NTSC only)ONanalogue video signals (composite, Y/C). (For recording and play-
back).
FOOT SWOFFSet this menu item when an external switch (e.g., a footswitch) is
L EDGEconnected to the SERIAL REMOTE terminal. Before using an ex-OFF : does not apply the setups.
ON : applies the setups
H EDGEternal switch (footswitch), please engage the recording pause or
L LEVELrecording mode.Memo
Y If dubbing is repeatedly done with the settings of the playback or
OFF: Use this setting if the external switch is not used.
recording video signals differing from the setting here, the hue
L EDGE: Recording and recording pause is switched at theand brightness of the video may turn out abnormal.
LOW edge of the external switch signal.
H EDGE: Recording and recording pause is switched at thePAGE BACKReturn to the TOP MENU.
HIGH edge of the external switch signal.
L LEVEL: Record at the LOW edge and pause recording at the
HIGH edge of the external switch signal.
PAGE BACKReturn to the REMOTE (1/2) menu.
6061 |
ACEC
JVC
