NAMES AND FUNCTIONS OF PARTS
Rear panel (continued)
e[SERIAL REMOTE] terminal (mini jack)
This terminal is for connecting to the serial
remote controller.
gTo operate BR-HD50 with this terminal, per-
form the following settings.
?Set REMOTE SEL SER in the REMOTE [1/
2] Menu screen to ?ON? or ?LOC+REM?.
ON:When the 5 REMOTE/LOCAL
switch on the front panel is set to
?REMOTE?, this terminal becomes
d
effective.
LOC+REM :This terminal is effective regard-
less of the setting of the 5
c baefhREMOTE/LOCAL switch on the
front panel.
a[IEEE1394] IEEE1394 terminal (6P)?Torecord a time code via this terminal, set
This is the input/output terminal for IEEE1394-TC DUPLI.: DV in the TC/UB/CLOCK [1/2]Memo
compliant digital signals.Menu screen to AUTO or NONDROP. (InTo use this terminal as the foot switch input, set
Inputs HDV signals or DV signals whenDV mode only)FOOT SW in the REMOTE [2/2] Menu screen.
recording. Digital audio is input simulta-?Tocontrol this unit via this terminal, set(XPage 71)
neously.REM SEL HDV/DV in the REMOTE [1/2]
During playback, it outputs HDV signals, DVMenu screen to ON or LOC/REM.f[REMOTE] RS-422A terminal
signals, and digital audio on the playback tape.(D-SUB 9P)
Note
Upon analog signal input, EE images and EEIf HDV/DV signals are not input/output when theThis terminal is for connecting to an RS-422A
audio are output. EE images are DV formatserial interface-compatible editing remote con-
IEEE1394 cable is connected, check whether the
signals (480i or 576i) (Only when IEEE1394signal format matches the IEEE1394 switch set-troller (e.g. RM-G820).
switch is set to DV).ting on the front panel. If the settings match,With this terminal, BR-HD50 can be used as a
?This unit records and plays 720p formatplayer of an editing system.
either reconnect the IEEE1394 cable, or reset the
HDV signals.power to the unit.To operate BR-HD50 with RS-422A, perform
720p HDV signals and DV signals from thisthe following settings.
terminal are recorded as is, without formatbDC power input terminal?Set REMOTE SEL 9P in the REMOTE [1/2]
conversion.Menu screen to ?ON?.
This terminal is for inputting DC 12 V. Connect
?To enable signal input via this terminal, setthe DC power cord of the supplied AC adapter.?Set the 5 REMOTE/LOCAL switch on the
the INPUT SELECT switch located on thefront panel to ?REMOTE?.
front panel to ?HDV/DV?.Memo
?The IEEE1394 switch located on the frontz When power is supplied to this terminal, theMemo
Screws for securing connectors differ by region.
panel must be set to ?HDV? or ?DV?, accord-OPERATE indicator located on the front panel
ing to the input signal to this terminal or thelights up. (The indicator turns red when BR-U model: inch screws
E model : metric screws
video format of the playback tape.HD50 is in the OPERATE OFF state)
?The audio mode (48kHz or 32kHz) cannotz Whether to set BR-HD50 to enter the OPER-
be changed for the input audio signal viaATE ON mode or OPERATE OFF mode whengFan
this terminal. It will be recorded using thepower is supplied to the terminal can beThis is a ventilation port for the fan motor.
input signal audio mode. 4-channel record-selected with DC IN MODE in the SYSTEM [2/Do not place objects in this area.
ing is possible in the 32kHz audio mode.2] Menu screen.hSlot cover for servicing
?Power cannot be supplied via this terminal.This is used for servicing the unit.
cDC power cord clamp
Use this clamp to fasten the DC power cord.
d[SIGNAL GND] terminal
This is the grounding terminal for signals.
E-18E-19 |
ACEC
JVC
