RECORDINGRECORDING
Recording procedureBackup recording function
In combination with DV equipment, BR-HD50 can perform continuous, long-hour recording.
BR-HD50 can be set as the backup unit connected to a DVcamcorder (GY-DV300/DV500/DV550/
2. REC button2.4.PLAY button
DV5000, etc.). When the recording tape of the source unit nears its end, BR-HD50 can start recording,
enabling long-hour recording.
Backup unit: BR-HD50
3.PAUSE
button
IEEE1394 cable
IEEE1394
DV terminal
terminal
INPUT SELECT switch
REMOTE/LOCAL switch
? For using GY-DV5000/DV5100 as the
Connection
source unit
5. STOP buttonConnect the DV terminal of the source unit to theSet DV REC TRIGGER in the OTHERS [1/2]
IEEE1394 terminal of BR-HD50 with an IEEE1394Menu screen of GY-DV5000/DV5100 to OFF.
1.Load the cassette tape.
Memocable.
?Before loading the cassette tape, please ensure that the rearOperation
z The tape protection function
slide of the cassette tape is pushed to REC.Setting up BR-HD50
enables BR-HD50 automati-1.Recording begins on the source unit.
J The unit is turned on.
cally to go into the STOP? Set the INPUT SELECT switch on the*Ensure that recording starts from the begin-
2.Start recording.
mode when there is a longfront panel to ?HDV/DV?.ning of the recording tape.
?Press the PLAY button while holding down the REC button.recording pause. The time to
? Set the REMOTE/LOCAL switch on the2.BR-HD50 begins recording when the tape of
3.Pause recording.go into the STOP mode can
front panel to ?REMOTE?.the source unit nears its end (about 5 min-
?Press the PAUSE button.be set with REC LONG P.
utes before the end of the tape).
4.Resume recording.TIME in the SYSTEM [1/2]? Set BACKUP REC: DV in the SYSTEM?BR-HD50 begins recording when the record-
?Press the PLAY button.Menu screen.[1/2] Menu screen.ing time of the source unit reaches the time
Use the following settings according to the
5.Stop recording.z When a home-use DV VCRset by BACKUP REC: DV.
?Press the STOP button.is used to play tapes record-tape length of the source unit.
ed with BR-HD50, the sound*For DV or mini DV cassette tape:Memo
level may be reduced.25MIN : 30-minute tapez In backup recording, BR-HD50 records video/
55MIN : 60-minute tapesound from the source unit.
75MIN : 80-minute tapeWhile this unit is performing backup recording,
Recording index signals115MIN : 120-minute tapecontinue shooting from the source unit.
z The audio mode is the one selected in the
If INDEX WRITE is set to ON in the SYSTEM [2/2] Menu screen, an index signal is recorded at the175MIN : 180-minute tape
recording starting position of the tape. In the PLAYBACK mode, the position where the index signal is265MIN : 270-minute tapesource unit. (32 k/48 k)
OFF: No backup recording
recorded can be searched. (Index search)z Set BACKUP REC: DV to ?OFF? if the unit is
not performing backup recording.
? Press the REC button to record index signals during? Set the REM SEL HDV/DV in the RE-
Memo
recording.z If recording is performedMOTE [1/2] Menu screen to ON or
* It is not possible to record only index signals after the record-LOC+REM.
right after the RECORDING
ing. Allow at least an interval of 1 minute between recordingsPAUSE mode is exited, in-? Set TC DUPLI.: DV in the TC/UB/CLOCK
of index.
dex signals are not record-[1/2] Menu screen to OFF.
*Index signals cannot be recorded with the REC button of the
ed.? It records the data of the built-in time code
remote controller. Use the record button of BR-HD50.
generator.
?When TC DUPLI.: DV is set to AUTO or
NON DROP, the time code of the DV cam-
corder will stop advancing. If the DV cable
is disconnected, the time code of the
backup recording will stop advancing.
E-46E-47 |
ACEC
JVC
