#5-)1 725'
&OHMJTI".�?´
REMOTE specifications
This monitor can be operated by remote control using the
Function
GPI connector and RS-232C connector.Description
Operation condition
INPUT SEL. SDI1This switches the input channel to SDI 1.
GPI connector<Note>
Edge operation
This function is not valid when OFF has been selected as
The items on the GPI screen correspond to the connector
the SDI 1 item (see page 20) setting on the FORMAT
pins shown below. Functions can be allocated to these pins
screen.
on the GPI screen of the main menu. (Refer to page 19)
INPUT SEL. SDI2This switches the input channel to SDI 2.
The functions allocated to the pins are enabled when the
<Note>
corresponding pin is shorted (ON) to the GND pin andThis function is not valid when OFF has been selected asEdge operation
disabled when it is left open (OFF).the SDI 2 item (see page 20) setting on the FORMAT
screen.
54321Pin no.Signal
INPUT SEL. VIDEO This switches the input channel to VIDEO.
1GPI1<Note>
9876
Edge operation
This function is not valid when OFF has been selected as
2GPI2
the VIDEO item (see page 20) setting on the FORMAT
Connector (9P) 3GPI3screen.
4GPI4INPUT SEL.This switches the input channel to ANALOG.
YPBPR/RGB<Note>
5GNDThis function is not valid when OFF has been selected as
Edge operation
6GPI5the YPBPR/RGB item (see page 20) setting on the
FORMAT screen.
7GPI6
SD ASPECTThis sets the aspect ratio of the SD images. However, it
8GPI7is not valid if a setting other than GPI has been selected
Level operation
for the SD ASPECT item on the VIDEO CONFIG screen.
9GPI8
<Note>
This function is not valid when HD signals are supplied.
HD ZOOMThis performs the HD ZOOM operations. (For details on
List of functions allocated
HD ZOOM, refer to page 5.)
The function which can be allocated to the pins are listedLevel operation
<Notes>
below.e This function is not valid when SD signals are supplied.
e It is not valid when FRONT has been selected as the
FunctionHD ZOOM item setting on the SYSTEM CONFIG
Description
screen.
Operation condition
BACKLIGHT MIN.This sets the backlight brightness to the minimum level.
UNDEFNot set (no function allocated)
<Note>
Level operation
MARKER1 ON/OFF This displays the markers which have been set by theThe setting for the BACKLIGHT item can be changed on
GPI PRESET1 item on the MARKER screen. (Refer tothe SYSTEM CONFIG screen while BACKLIGHT MIN. is
Level operation
page 16) However, it is not valid when MENU has beenkept at ON. When BACKLIGHT MIN. is set to OFF and
selected as the MARKER SELECT item setting on theback to ON at this time, the brightness will be set to the
MARKER screen.minimum level.
<Note>
R TALLYFor lighting up the red tally lamp.
When this function has been set to ON at the same time
as MARKER2, MARKER1 takes precedence.Level operation
MARKER2 ON/OFF This displays the markers which have been set by theG TALLYFor lighting up the green tally lamp.
GPI PRESET2 item on the MARKER screen. (Refer to
Level operationLevel operation
page 16) However, it is not valid when MENU has been
selected as the MARKER SELECT item setting on theMONO ON/OFFFor setting the images to the monochrome mode.
However, this function is not valid when a setting other
MARKER screen.
Level operation
than GPI has been selected for the MONO item on the
MARKER BACKThis sets the background brightness to 50% when 4:3,VIDEO CONFIG screen.
HALF13:9 or 14:9 has been selected for the GPI PRESET1
GAMMA SELECTThis switches the gamma setting to FILM. (Refer to page
item setting on the MARKER screen. However, it is not
Level operation18)
valid when MENU has been selected as the MARKERLevel operation
SELECT item setting on the MARKER screen.
WFM ON/OFFThis displays the Y signal (brightness) waveforms.
MARKER BACKThis sets the background brightness to 0% when 4:3,Level operation
BLACK13:9 or 14:9 has been selected for the GPI PRESET1
item setting on the MARKER screen. However, it is not
Level operation* Concerning the operation conditions
valid when MENU has been selected as the MARKER
Level operation: The function is operational while the pin to which it has
SELECT item setting on the MARKER screen.
been allocated is shorted to ground.
<Note>
Edge operation: The function is operational when the pin to which it has
When this function has been set to ON at the same time
been allocated changes from open to shorted to ground.
as MARKER BACK HALF, MARKER BACK BLACK takes
<Note>
precedence.
If a function whose operation condition is triggered by the level has been
CENTER MARKER This displays the center marker.allocated to a multiple number of pins, it will continue to be operational
However, it is not valid when MENU has been selectedwhile any one of those pins is shorted.
Level operation
as the MARKER SELECT item setting on the MARKER
screen.
<Note>
When any other markers are displayed, the center
marker is superimposed onto the same display.
22 |
ACEC
PANASONIC
