CDX-F5500/F5505X
GeneralY US, Canadian model
OutputsAudio outputs terminal
(front, rear/sub switchable)
CAUTION
Power antenna/aerial relay control terminal
Use of controls or adjustments or performance of procedures
Power amplifier control terminal
InputsTelephone ATT control terminalother than those specified herein may result in hazardous
Remote controller input terminalradiation exposure.
BUS control input terminal
BUS audio input terminal
If the optical pick-up block is defective, please replace the whole
Antenna/aerial input terminal
Tone controlsLow: ?10 dB at 60 Hz (XPLOD)optical pick-up block.
Mid: ?10 dB at 1 kHz (XPLOD)Never turn the semi-fixed resistor located at the side of optical
High: ?10 dB at 10 kHz (XPLOD)
pick-up block.
Power requirements12 V DC car battery
(negative ground)
DimensionsApprox. 178 � 50 � 181 mm
optical pick-up
(7 1/8 � 2 � 7 1/4 in)
(w/h/d)
Mounting dimensionsApprox. 182 � 53 � 161 mm
(7 1/4 � 2 1/8 � 6 3/8 in)
(w/h/d)
MassApprox. 1.2 kg
Supplied accessoriesCard remote commander RM-X115
Parts for installation and connections (1 set)
Front panel case (1)
Design and specifications are subject to change without
notice.
SERVICE NOTES
Y AEP, UK, E model
semi-fixed resistor
This label is located on the bottom of the chassis.
TEST DISCS
This set can playback CD-R and CD-ROM discs. The following
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCKtest discs should be used to check the capability:
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostaticCD-R test disc TCD-R082LMT (Part No. J-2502-063-1)
breakdown because of the potential difference generaCD-Rted bW test disc y theTCD-W082L (Part No. J-2502-063-2)
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, ob-
serve from more than 30 cm away from the objective lens.
Notes on Chip Component Replacement
? Never reuse a disconnected chip component.
? Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
ATTENTION AU COMPOSANT AYANT RAPPORT
SAFETY-RELATED COMPONENT WARNING!! � LA S?CURIT?!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINELES COMPOSANTS IDENTIFI?S PAR UNE MARQUE 0 SUR LES
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INDIAGRAMMES SCH?MATIQUES ET LA LISTE DES PIéCES
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.SONT CRITIQUES POUR LA S?CURIT? DE FONCTIONNEMENT.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSENE REMPLACER CES COMPOSANTS QUE PAR DES PIéCES
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL ORSONY DONT LES NUM?ROS SONT DONN?S DANS CE MANUEL
IN SUPPLEMENTS PUBLISHED BY SONY.OU DANS LES SUPPL?MENTS PUBLI?S PAR SONY.
2 |
ACEC
SONY
