? ? or ? ? button and press ? ? or ? ? button. To cancel A.P.S.S..Sleep Timer Last Minute Indicator
during running press ? ? or ? ? button.It is displayed on the upper right of the screen. If sleep timer is
After A.P.S. is finalized, a programme list will apper on theactivated it is displayed with the TV status and erased with it
screen. In the programme list you will see the programmeafter 3 seconds.
numbers and names assigned to the programmes.If there is only one minute of the countdown left of the timer, it
If you do not accept the locations and/or the programmeis displayed automatically on the upper left of the screen, and
names of programmes, you can change them in Programmestays there until time is reached. Then TV goes automatically
menu.to stand-by.
Other Features
Mute Indicator
TV Status
It is placed in the upper middle of the screen when enabled,
Programme Number, Programme Name (or AV), (they areand it stays there until it is disabled.
displayed on the upper left of the screen) and Sleep Timer
(shows the time left on the upper right screen if enabled). In
stereo options the sound indicator is displayed with them too.To cancel mute, there are two alternative; the first one is press-
They are displayed after programme change for 3 seconds.ing to " " button, thus volume is set to the preceding value,
Programme Numberand the second one is increasing the volume level, thus it
starts at the minimum level to increase. By decreasing the
Programme Name (5 characters)volume level in mute state, mute will not be ignored, only the
volume level will decrease. If mute is cancelled after decreas-
These OSD?s are displayed when a new programme is en-
ing the volume level, the volume will return at the decreased
tered by digit button, by pressing ?P<P? button, or by ? ? or ? ?level.
button, or by ?TV ? button.No-Signal
Programme Swap (P<P)No-Signal Timer Indicator
This button is used to re-enter the preceding entered pro-It is displayed in the middle of the screen when no valid sig-
gramme again. Pressing "P<P" consecutively allows to swapnal detected. It shows the time remaining before the switch-
into two last entered programmes.ing to the Stand-By mode (it takes 5 minutes when no signal
detected or no any Remote Control command is accessed).
The indicator is displayed for 3 seconds when there is no valid
signal.
After a Remote Control command (if No-Signal Timer is active)
the timer stops and if no signal detected again the timer is ini-
tialized to 5 minutes and starts 3 seconds later again to count
down.
It is not valid in AV mode.
Double-digit (- -)Blue Background During No-Signal
This OSD is displayed when the "Double-Digit" button pressedIn case, no valid signal is detected (in TV or AV mode) Blue Back-
in place of the programme number indicator.ground is activated.During search process Blue Background
is not active. But instead there is another feature given; the
semi-transparent menu background is becomes blue.
After that, in order to enter a programme press two digits con-
secutively. Both digits must be entered within 3 seconds or theVolume Bar
function will disappear.It is displayed in the lower middle of the screen. When a vol-
ume command is received (pressing ?VOL+? or ?VOL-? by
Personal Preferences (PP)Remote Control or Front panel) and no menu is active, it stays
All the preset values will be restored, when pressing "PP".on the screen for 3 seconds, after the last volume command
or until another command is received in between.
Picture Mode
AV Modes
If your TV has the WSS feature, the picture mode OSD is dis-
played below the sound indicator, by TV Status OSD?s. Accord-By pressing the ?AV ? button you can switch your TV to AVV
ing to the WSS data, inside of the OSD box ?4:3? or ?16:9? ormodes (except being in Teletext). Pressing this button
?AUTO? is written.consecutively will switch the TV in one off the AV modes: AV-1,
F-AV, RGB.
By pressing ?? (TXT_UPDATE) button (if Teletext is not ac-
tive) the picture mode can be switched into 4:3, 16:9 or AutoAV-1 supports the RGB mode. But if there is some colour prob-
Mode.lem in AV-1 mode, please force the AV mode to RGB mode.
In order to quit the AV mode press the ?TV ? button.
GB - 12 -
ACEC
HITACHI
