Applications (Advanced operations)
7 To program Loop play information
Remote control unit
Loop play information can be programmed into a HOT CUE
LOOP OUTEMERGENCYbutton to allow one-touch loop play. See the section OHot
LOOP IN/EXIT/
/OUT ADJLOOP
REALTIME CUERELOOPCue� (p. 15).
7 To automatically set loop end (Emergency Loop)
During playback, press the EMERGENCY LOOP button.
? Normal loop play display occurs (button flashes and LOOP
SEARCHindicator lights), and EMERGENCY LOOP indicator
(1,!)
flashes.
PLAY/? The point at which the button is pressed becomes the
PAUSE
(3 8) loop in-point, and a loop out-point will be set automatically
as follows:
Jog dial? If the immediately preceding BPM value is known, the
loop out-point will be set 4 beats after the loop in-point.
? If the immediately preceding BPM value is not known,
Loop Playback (*)the loop out-point will be set 4 seconds after the loop
in-point.
7 Defining a loop? If either of the above conditions (4 beats later or 4
1. Press the PLAY/PAUSE button (38) to beginseconds later) occurs later than the track end, the track
playback.end will be set as the loop out-point.
2. During playback, press the LOOP IN/REALTIME CUE? If the EXIT/RELOOP button is pressed, loop playback is
button at the point from which you wish to start thecanceled and normal playback resumes.
loop.
? Note that this operation need not be performed if aWAVE Display (*)
prerecorded cueing point is to be used as the loop in-
point.
This display shows the trackOs low tone beats (bass drum, etc.),
3. During playback, press the LOOP OUT/OUT ADJ
thus letting you know the trackOs break points and end points.
button at the point from which you wish to end the
? Together with playback of the current track, the WAVE is
loop.
displayed.
? Loop playback will begin, with playback looping from
Once displayed, the WAVE information is memorized, so that
the loop in-point to the loop out-point.
it will be displayed immediately next time. Setting contents
for the original disc cannot be read, however, in the case of
7 Stopping loop playback
discs copied to CD-R or CD-RW.
During loop playback, press the EXIT/RELOOP button.
? Up to 99 tracks can be memorized for each disc.
? Once this has been done, playback will continue in
? In the event a track has little change in low-register beat
sequence from the loop out-point without returning to the
levels, the break point may not be displayed correctly.
loop in-point.
? During playback, if operations such as scan, jog dial, or pause
are attempted, the WAVE data may fail to be recorded in the
7 Changing the loop out-pointvicinity where the said operation was attempted. In that case,
1. During loop playback, press the LOOP OUT/OUT ADJrerecording of the WAVE data is required.
button.
? The loop out-point time will be displayed on the display
CD TEXT Display
panel, the LOOP OUT/OUT ADJ button will begin
flashing rapidly, and the IN/REALTIME CUE button will
CDs supporting CD TEXT function will show a consecutively
be unlit.
scrolling display of the disc title and track title (limited to
2. Press the forward or reverse SEARCH button (1,
alphanumerics and certain symbol characters). During display of
!) or turn the Jog dial.
the disc title, the disc mark lights.
? The loop out-point will be shifted forward or backward
in 1-frame units.
? Pressing the LOOP OUT/OUT ADJ button or waiting for
30 seconds or longer will cause the player to exit from
update loop input point mode and to resume loop
playback.
7 Returning to loop playback
After loop playback has been stopped, press the EXIT/
RELOOP button during playback to return to loop
playback.
? The player will return to the currently defined loop in-point
and begin loop playback (i.e., relooping) again from that
point.
16<DRB1307> |
ACEC
PIONEER
