The operating instructions mentioned here are partial abstracts SECTION 1
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remain as in the manual.GENERAL
Use of the tilt-swivel
PrecautionsThis monitor can be adjusted within the angles shown below. To Identifying parts and controls
find the center of the monitorOs turning radius, align the center of
Warning on power connectionsthe monitorOs screen with the centering dots on the stand.See the pages in parentheses for further details.
Y Use the supplied power cord. If you use a different power cord, Hold the monitor at the bottom with both hands when you turn it
be sure that it is compatible with your local power supply.horizontally or vertically. Be careful not to pinch your fingers at FrontRearforward sideforward side
For the customers in the U.S.A.the back of the monitor when you tilt the monitor up vertically.
If you do not use the appropriate cord, this monitor will not
conform to mandatory FCC standards.rear siderear side
Example of plug typesMENUAC IN
90uRESETINPUTHD15BNC
15u
RGBHDVD
(HD15)(BNC)
90u
5uMENU
RESETINPUTHD15BNC
for 100 to 120 V ACfor 200 to 240 V AC
Y Before disconnecting the power cord, wait at least 30 seconds
after turning off the power to allow the static electricity on the
screenOs surface to discharge.Centering dots
Y After the power is turned on, the screen is demagnetized
(degaussed) for about 2 seconds. This generates a strong
magnetic field around the screen which may affect data stored 1 RESET (reset) button (page 16)6 Video input 1 connector (HD15) (y1) (page 6)
on magnetic tapes and disks placed near the monitor. Be sure to This button resets the adjustments to the factory settings.This connector inputs RGB video signals (0.700 Vp-p,
keep magnetic recording equipment, tapes, and disks away positive) and sync signals.
from the monitor.2 INPUT (input) switch (page 8)
This switch selects the HD15 or BNC video input signal.5 4 3 2 1
1-1The equipment should be installed near an easily accessible 10 9 8 7 6US
3 Control button (page 10)
outlet.15 14 13 12 11
The control button is used to display the menu and make
adjustments to the monitor, including brightness and contrast
Installationadjustments.Pin No.Signal
Do not install the monitor in the following places:
Y on surfaces (rugs, blankets, etc.) or near materials (curtains, 4 1 (power) switch and indicator (pages 7, 16, 20)1Red
draperies, etc.) that may block the ventilation holesThis button turns the monitor on and off. The power indicator 2Green
Y near heat sources such as radiators or air ducts, or in a place lights up in green when the monitor is turned on, and either (Sync on Green)
subject to direct sunlightflashes in green and orange, or lights up in orange when the 3Blue
Y in a place subject to severe temperature changesmonitor is in power saving mode.
Y in a place subject to mechanical vibration or shock4ID (Ground)
Y on an unstable surface5 AC IN connector (page 7)5DDC Ground*
Y near equipment which generates magnetism, such as a This connector provides AC power to the monitor.
6Red Ground
transformer or high voltage power lines
Y near or on an electrically charged metal surface7Green Ground
8Blue Ground
Maintenance
9DDC + 5V*
Y Clean the screen with a soft cloth. If you use a glass cleaning
liquid, do not use any type of cleaner containing an anti-static 10Ground
solution or similar additive as this may scratch the screenOs 11ID (Ground)
coating.
12Bi-Directional Data (SDA)*
Y Do not rub, touch, or tap the surface of the screen with sharp or
abrasive items such as a ballpoint pen or screwdriver. This type 13H. Sync
of contact may result in a scratched picture tube.14V. Sync
Y Clean the cabinet, panel and controls with a soft cloth lightly
moistened with a mild detergent solution. Do not use any type 15Data Clock (SCL)*
of abrasive pad, scouring powder or solvent, such as alcohol or * DDC (Display Data Channel) is a standard of VESA.
benzene.
7 Video input 2 connector (BNC) (y2) (page 6)
Transportation
This connector inputs RGB video signals (0.700 Vp-p,
When you transport this monitor for repair or shipment, use the positive) and sync signals.
original carton and packing materials.
45 |
ACEC
SONY
