EE
NN
Installation Guide (Continued)
GG
LL
II
SS
Speakers
HP Final ChecksP Installation ProceduresH
Connect the speaker wires. See the wiring diagram
1. Make sure that all wires are properly connectedFirst complete the electrical connections, andInsert mounting collar 1 into the dashboard, and
1112
(! page 32) for the proper hookups. Follow the di-
and insulated.then check them for correctness. (! page 32)1bend the mounting tabs out with a screwdriver.
agram carefully to avoid damaging the speakers
2. Make sure that the stereo unit is securely held inMake sure that the lock lever (§) is �ush with the
and the stereo unit.
the mounting collar.mounting collar 1 (not projecting outward).
The speakers used must be able to handle more
3. Turn on the ignition to check the unit for proper
than 45 W of audio power. If using an optionalLock lever (§)
operation.
audio ampliŢer, the speakers should be able to han-
dle the maximum ampliŢer output power. SpeakersIf you have difficulties, consult your nearest author-
with low input ratings can be damaged. Speakerized professional installer for assistance.
impedance should measure 4�8 `, which is typi-
cally marked on most speakers. Lower or higher
P Preparation
impedance speakers will affect output and can
cause both speaker and stereo unit damage.eWe strongly recommend that you wear gloves
for installation work to protect yourself from
Motor Antenna6 Power connector
injuries.Lock lever (§)
Connect the car motor antenna lead to the dark
eWhen bending the mounting tabs of the
blue motor antenna relay control lead.
mounting collar with a screwdriver, be careful
Batterynot to injure your hands and Ţngers.
Connect the yellow battery lead to the correct radio
wire or to the battery fuse port on the fuse block.eDisconnect the cable from the negative - batteryMounting tabs
terminal (see caution below).5 Mounting bolt
Antenna
eUnit should be installed in a horizontal position
Connect the antenna by plugging the antenna leadSecure the rear of the unit.
with the front end up at a convenient angle, but
into the antenna receptacle.2After Ţxing mounting bolt 5 and power connector
not more than 30o.
6, Ţx the rear of the unit to the car body by either
Equipment
method (a) or (b) shown below.
Connect any optional equipment such as an ampli-
Å¢er, according to the instructions furnished withInsert trim plate 7.
the equipment. Leave about 30 cm of distance be-3
tween the speaker leads/ampliŢer unit and the an-
Less than 30xAfter installation, reconnect the negative -
tenna/antenna extension cord. Read the operating
4
battery terminal.
and installation instructions of any equipment you
will connect to this unit.
Caution:
Power
eDo not disconnect the battery terminals of a
Connect the red power lead to the correct car radio
car with a trip or navigational computer since
wire or to the appropriate fuse port on the fuse
all user settings stored in memory will be lost.
block.
Instead take extra care with installing the unit
If the stereo unit functions properly with all these
to prevent shorts.(a) Using the rear support strap 3(b) Using the rubber cushion (option)
connections made, disconnect the wires and pro-
Fire wall of car
ceed to the Ţnal installation.
Dashboard Installation4 Tapping screwRear support bracket
Rubber cushion (option)
Installation Opening(5 mm?a16 mm)3 mm?(provided on the car)
P Final Installation
2 Hex. nut
Lead Connections53 mm
(5 mm?)
Connect all wires, making sure that each connec-
182 mm3 Rear supporttion is insulated and secure. Bundle all loose wires
and fasten them with tape so they will not fall down5 Mounting bolt
strap
later. Now insert the stereo unit into the mountingThis unit can be installed in any dashboard having
(5 mm?)
5 Mounting boltcollar.
an opening as shown above. The dashboard should
(5 mm?)
1 Mounting collar
Congratulations! After making a few Ţnal checks,be 4.75 mmj5.56 mm thick in order to be able to
1 Mounting collar
youOre ready to enjoy your new auto stereo system.support the unit.
2829
CQ-DP151/DP101WCQ-DP151/DP101W |
ACEC
PANASONIC
