EE
NN
GInstallation (Continued)G
LL
II
SS
Cautions:
HP PreparationP Installation HardwareH
!We strongly recommend that you wear gloves for installation work to protect yourself from injuries.
Warning: If your car is equipped with air bag
17!When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure your18
and/or anti-theft systems, specific proceduresNo.ItemDiagram QOty
hands and fingers.
may be required for connection and disconnec-
Mounting Collar*
tion of the battery to install this product. q1
(FX0214C316ZA)Insert Mounting Collar q into the dash-
First complete the electrical connections, and
Before attempting installation of this electronic
Hex. nut (5 mmż)then check them for correctness.(a page 30)1board, and bend the mounting tabs out
component, contact your car dealer or manufac-
w1
turer to determine the required procedure and(YJN994C002ZA)The included Mounting Collar q iswith a screwdriver.
designed specially for this unit. Do
strictly follow their instructions. The tabs to be bent vary depending on
Rear support strap
enot use it to attach any other model.FAILURE TO FOLLOW THE PROCEDURE MAY1the car. To securely install the unit, fully(YFG044C002ZA)
RESULT IN THE UNINTENDED DEPLOYMENT OFbend a number of the tabs so that there
Tapping screw (5 mmż�16 mm)is no rattling.AIR BAGS OR ACTIVATION OF THE ANTI-THEFT
r1
(XTT5+16AFK)Example:SYSTEM RESULTING IN DAMAGE TO THE VEHI-Tab
CLE AND PERSONAL INJURY.
Mounting Bolt (5 mmż)
t1
Y Disconnect the cable from the negative battery (YEJV014C002A)
terminal (see warning and caution below).
Power Connector
y1
Y Remove Mounting Collar q and Trim Plate u from the(YEAJ02877)q Mounting
y Power Connector
Collar
main unit temporarily, which are already mounted at
Trim Plate*
shipment.*u1
(YFC054C063ZA)
Caution: Various settings that have been stored in theDismounting Plate
memory in other on-board equipment (car navigationi(YFX214C323ZA)2
etc.) may be lost if the battery terminals are discon-
nected.
Mounting Holes
Therefore, we recommend to make a record of or to
(a) Using the rear support strap et Mounting Bolt
back up the settings before disconnecting the termi-
Fire wall of car
nals.
r Tapping screw
After completing installation of the main unit, set theEstablish the rear connection of the unit.
(5 mmż�16 mm)3 mmż
equipment again according to the record.After fixing Mounting Bolt t and Power Connector
2
w Hex. nuty, fix the rear of the unit to the car body by either
Y Unit should be installed in a horizontal position with theMounting Springs (C)
(5 mmż)method (a) or (b) shown the previous page.
front end up at a convenient angle, but not more than 30!.
e Rear support strap
Insert Trim Plate u.
3
t Mounting bolt (5 mmż)
q Mounting collar
Less than 30!
After installation reconnect the negative
4(�) battery terminal.
(b) Using the rubber cushion (option)
P Dashboard Installation
Rear support bracket
Installation OpeningRubber cushion (option) (provided on the car)
This unit can be installed in any dashboard having
an opening as shown below. The dashboard should
be 3 � 16" (4.75 mm)�7 � 32" (5.56 mm) thick inEngage the Mounting
order to be able to support the unit.Springs (C) in the
t Mounting boltMounting
mounting holes of the
(5 mmż)
23/32"Mounting Collar qHole
(53 mm)firmly.
q Mounting collar
75/32"Mounting Spring
(182 mm)
2829
CQ-C1200U/C1120U/C1110U/C1100UCQ-C1200U/C1120U/C1110U/C1100U |
ACEC
PANASONIC
